User manual SANUS VISIONMOUNT DUAL-SIDED CEILING MOUNT-LC2A

[. . . ] The VisionMountTM LC2A is designed to mount two flat panel televisions up to 1270 mm (50 in) and weighing up to 59 kg (130 lb) each to an existing NPT 1-1/2 threaded pipe drop. The LC2A tilts the televisions from +5° to -15°, swivel up to ±90°, and roll ±6°. [. . . ] Replacement parts for products purchased through authorized dealers are shipped directly to you. [01] X 1 [02] X 1 [03] X 2 [04] X 4 [05] X 8 [06] X 4 Sanus Systems 2221 Hwy 36 West, St Paul, MN 55113 USA · 01. 04. 07 (6901-100129<00>) USA Customer Service 800. 359. 5520 · www. sanus. com 1/4-20 x 2. 0 in. [07] X 8 [08] X 8 1/4-20 [09] X 2 [10] X 2 [11] X 10 [12] X 1 [13] X 1 [14] X 1 [15] X 8 [16] X 8 [17] X 8 [18] X 8 M4 x 30mm M5 x 30mm M6 x 35mm M8 x 40mm [19] X 8 [20] X 8 [21] X 8 [22] X 8 [23] X 8 [24] X 8 [25] X 8 [26] X 8 [27] X 16 [28] X 8 [29] X 8 [30] X 8 2 6901-100129<00> 1 1 -1: TV with flat back 1 - 2: TV with curved back or obstruction 1-1 [27] [27] [23] [24] [15] [16] 1-2 [29] [27] [27] [23] [19] [29] [27] [27] [24] [20] M5 x 30mm M4 x 30mm [28] [25] [17] [30] [--] [28] [25] [21] M6 x 35mm [28] [26] [18] [30] [--] [28] [26] [22] M8 x 40mm [06] [06] 8x 6901-100129<00> 3 2 Do not overtighten the Nut [08]. The vise Assembly [05] must rotate freely around the Carriage Bolt [07]. [05] [07] 8x [08] [06] 1/4-20 x 2. 0 in. 3 3 -1 [04] [06] [04] [05] 4 6901-100129<00> CAUTION: To prevent property damage and/or personal injury, the CrossTubes [04] must extend beyond the outside edges of both Monitor Brackets [06]. Orient the Vise Assemblies [05] and [A] on both the Axis Assembly [03] and the second Monitor Bracket [06] so that the Cross Tubes [04] pass between the jaws. Do not over-tighten the four Vise Assemblies [05] and the two Vise Assemblies [A] . Turn the Allen Bolt until resistance is felt; then, tighten the Allen Bolt approximately 1 -1/2 turns or until the head of the Allen Bolt is slightly above the surface of the Vise Assembly. The Cross Tubes [04] will not be able to move side-to-side when the Vise Assembly is properly tightened. Tighten all six Allen Bolts on both TVs 3-2 [A] [06] [04] [03] [14] [05] [A] 4 [01] [02] 6901-100129<00> 5 5 Thread the Coupler [01] and Tube [02] onto an existing threaded pipe drop. Once the Tube [02] is properly aligned, tighten the Set Screws [10] using Allen Wrench (12) and the two Set Screws [B] on the Tube using Allen Wrench (13). [12] [13] [10] [02] [B] [01] [02] [10] 6 6 -1 6-2 For clairity, TV is not shown. [09] [03] [02] [02] [03] 6 2x 6901-100129<00> 7 To adjust for level, loosen the two Allen Bolts [C] on the back of the Axis Assembly [03]. To adjust tilt tension, loosen the Tension Knobs [D]. 7 -1 [14] 2x [C] [D] [03] CAUTION Never completely remove the Tension Nut [E]. Hex hole in Safety Bracket must seat completely down onto Tension Nut [E]. Failure to heed this Caution may result in property damage and/or personal injury. [. . . ] CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. 8 6901-100129<00> [. . . ]