User manual SANUS VISIONMOUNT CENTER CHANNEL SPEAKER MOUNT-VMCC1

[. . . ] See complementary Sanus products at www. sanus. com For assembly information for the VMSA, VMAA, VMAA18 and VMAA26 see the Steps 1 through 6. For assembly information for the VMDD and VMDD26 see Steps 7 through 12. Step 1: Remove mount from Wall Plate and remove lower Cross Tube from the mount assembly. Loosen the Allen Bolts in the lower three Vise Assemblies and remove the lower Cross Tube from the mount assembly. [. . . ] Thread a 1/4 - 20 x 5/8 Bolt (k) up through each of the Upper Extensions. Do not tighten the 1/4 - 20 x 5/8 Bolts at this time, you will tighten these so they bottom out into the Support Bar after the speaker is attached. Note: For Speakers that have threaded inserts that are spaced between 1. 75 inches and 15. 5 inches use configuration 1. If the threaded inserts on the speaker are spaced wider than 15. 5 inches, the tabs on the Speaker Brackets should face away from each other. Detailed View Diagram 6 e a, b j k Assembly Instructions for the VMDD and VMDD26 flat panel wall mounts. Step 7: Remove mount from Wall Plate and remove lower Cross Tube from the mount assembly. Loosen the Allen Bolts in the lower four Vise Assemblies and remove the lower Cross Tube from the mount assembly. Diagram 7 vise assemblies cross tube Step 8: Add Axis Brackets If the threaded inserts on your speaker are spaced between 1. 5 inches and 5. 7 inches, you do NOT need to use the Support Bar (g) for the installation. Position the Axis Bracket (d) so it fits the Axis Assembly on the mount. Insert 1/4 - 20 x 5/8 Bolt (k) through the outer side of the Axis Bracket, Axis Assembly, and into a 1/4 - 20 Nut (m). Insert a 1/4 - 20 x 1. 5 Bolt (n) through the inner side of the Axis Bracket, a Spacer (l), the inner edge of the adjacent Axis Bracket. Slide the Support Bar through the slots in each Axis Bracket until centered with the wall mount. Detailed View Diagram 8 k m l m axis assembly axis assembly n d d Step 9: Add Bar Brackets Note: If the Support Bar was not installed in Step 8, only re-install the cross tube in this step. Slide the lower Cross Tube through the first Monitor Bracket, first Bar Bracket (e), both Axis Assemblies, a second Bar Bracket and through the second Monitor Bracket. Tighten all four Vise Assemblies to secure the Cross Tube once it is slid through the second Monitor Bracket. Thread each 1/4 - 20 x 5/8 Bolt (k) through each hole in the bottom of the Axis Bracket (d) until they bottom out against the Support Bar (g). Diagram 9 Detailed View g d k Step 10: Configure Speaker Attachments - Support Bar Not installed. If using Support Bar, see Step 5 for configuration. Configure the Speaker Attachments as seen below. [. . . ] If the threaded inserts on the speaker are spaced wider than 15. 5 inches, the tabs on the Speaker Brackets should face away from each other. In Example shown below, Speaker Brackets are configured for the 5. 7 to 15. 5 range. Detailed View Diagram 12 e a, b j k Step 13: Add center channel to VMCC1 Slide the Bar Brackets (e) until the Speaker Brackets (f) line up with the threaded inserts on the back of the speaker. Select the proper bolt for your center channel speaker by hand threading the M4 x 10 Bolt (h), M5 x 10 Bolt (i) or 1/4 - 20 x 3/8 Bolt (j) into the into the threaded inserts in the back of the speaker to determine which fits. [. . . ]