User manual SANUS VF5023

[. . . ] The input plug of this power tap is intended to serve as the disconnect device, it shall be easily accessible and withdrawn. This power conditioner does not contain internal Circuit Breaker protection; INSTALLER MUST ensure that the input of this power conditioner is connected individually to an electrical service panel that is protected with a UL Listed 20A (Minimum) Circuit Breaker for overload protection of the power conditioner. Do not use this product for any purpose not explicitly specified by Sanus Systems. If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact Sanus Systems Customer Service or call a qualified contractor. [. . . ] If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact Sanus Systems Customer Service or call a qualified contractor. English Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Sanus Systems Customer Service. If the lights fail to illuminate see the troubleshooting section of this manual. VOLTS/AMPS/KW LED Display: Shows the operating voltage, operating current, and overall power consumption supplied by power conditioner. VOLTS/AMPS/KW Mode Button: Alternates between the three electrical measurements. English INSTALL VF5023 TO RACK RAILS Using rack rail screws attach the VF5023 to any 1U location on a 19 in. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (0-40°C/32-104°F) specified by the manufacturer. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. This warranty does not extend to any Sanus Systems product that has been damaged or rendered inoperable as intended or defective (a) as a result of accident, misuse or abuse; or (b) by the use of parts not manufactured or sold by Sanus Systems; or (c) by modification of the product. Connected Equipment Damage Warranty Sanus Systems will also provide you with a remedy for damage to connected equipment if (i) you have a claim that is covered by the limited product warranty described above, and (ii) Sanus Systems receives a formal warranty claim from you before the end of the warranty period for damage to connected applicable to the affected product. If the conditions listed in the preceding sentence are met, Sanus Systems will provide you with one of the following remedies, provided that it may decide at its sole discretion which remedy it provides. Sanus Systems will (1) replace the damaged connected equipment; (2) pay to repair the damaged connected equipment; or (3) pay you the fair market value of the connected equipment, provided that such payments shall not exceed (i) the maximum coverage amount for the product, or (ii) the amount of actual damage caused by power surges due to a product defect. nOTE: Compensation for restoration of data loss is not covered AND SANUS SYSTEMS DOES NOT ASSUME ANY LIABILITY FOR ANY INCIDENTAL , CONSEQUENTIAL OR INDIRECT DAMAGES UNDER THIS LIMITED WARRANTY. This Connected Equipment Damage Warranty does NOT cover damage caused by lightening or lightening strikes. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. If any provision of these limited warranties is unlawful, void or unenforceable, that provision shall be deemed severable and shall not affect any remaining provisions. In case of any inconsistency between the English and other versions of these limited warranties, the English version shall prevail. In the event damage has occurred to a Sanus Systems product or to connected equipment, you must contact Sanus Systems within thirty (30) days of the date you knew or should have known of the damages. [. . . ] In case of any inconsistency between the English and other versions of these limited warranties, the English version shall prevail. In the event damage has occurred to a Sanus Systems product or to connected equipment, you must contact Sanus Systems within thirty (30) days of the date you knew or should have known of the damages. These limited warranties and any disputes arising out of or in connection with these limited warranties ("Disputes") shall be governed by the laws of the State of Minnesota, USA, excluding the Convention for the International Sale of Goods. The courts located in the State of Minnesota, USA shall have exclusive jurisdiction over any Disputes. [. . . ]