User manual SANUS PLATINUM FURNITURE FLAT PANEL TV STAND-PFFP

[. . . ] Check carefully to make sure none of the parts are missing or defective. Replacement parts for products purchased from an authorized dealer will be shipped directly to you. Please call Sanus Systems before returning products to the retail store where you purchased them. Attach the Pillar (d) to the Base (a) by placing each M12 x 40 Bolt (m) through an M12 Washer (n), each M8 x 35 Bolt through an M8 Washer (s). [. . . ] Attach the Wall Bracket Spacers (i) to the Wall Bracket (c) by fitting the plastic tabs into the correct oval holes on the Wall Bracket as seen in the Detailed View of Diagram 5. Wall Bracket Spacers must be held in place while you slide the Wall Bracket Assembly down into place on the Pillar (d). Make sure the Wall Plate (f) fits into the channel in the Pillar as seen in the Top View of Diagram 5. Once the Wall Bracket Assembly is in the desired position, tighten the M8 Allen Bolts (q) with an Allen Key (ll) so the Wall Bracket Assembly is firmly attached to the Pillar. Take the Glass Shelf Washer (h) and insert it onto the Glass Shelf (b). make sure the holes in the Glass Shelf Washer and the Glass Shelf match up. Then, proceed to slide the Glass Shelf and the Glass Shelf Washer into the Shelf Bracket (g). Thread each 1/4-20 Allen Bolt (t) down through a Plastic Washer (u), the Glass Shelf, the Glass Shelf Washer, and into the Shelf Bracket. Next, add the Top Cap (j) to the top of the Pillar (d) by lining up the two plastic dowels on the bottom of the Top Cap with the corresponding pattern on the top of the Pillar as seen in Detailed View B of Diagram 6b. Step 7: Always make sure the television is unplugged before threading any bolt into the back panel!Thread bolts carefully into your television by hand before tightening. If you are unable to find appropriate hardware for your television, consult a local hardware store or call Sanus Systems. Locate the threaded inserts on the back of your flat panel television and determine which of the provided Bolts (v, w, x, y, z, aa, bb, cc) is the correct diameter. To test each diameter, thread the Bolts carefully into your television by hand until you find the diameter that correctly fits. If the back of your TV is flat, use one of the shorter Bolts without a Spacer. The back of some flat panel televisions are curved or have recessed threaded inserts. This may require you to use one of the longer Bolts, and a Spacer (ii, jj) between the television and the Monitor Bracket (k, l). Once you have the correct bolt selected, you can follow the diagrams below to see what additional hardware you will need to mount the Monitor Brackets to your TV. You will use four of each part every time it is listed below to attach the Monitor Brackets to your TV. Step 8: Attaching the Monitor Brackets to a TV with a flat back For a flat back TV that requires the M4 or M5 diameter Bolt, thread a M4 x 12 (v) or a M5 x 12 (x) Bolt through the appropriate Lock Washer (ee, ff), an M4/M5 Washer (dd), the Monitor Bracket (k, l) and finally into the TV. [. . . ] To hang the TV onto the Wall Bracket (c) first hook the Monitor Brackets (k, l) over the top of the Wall Bracket, then let the bottom of the Monitor Brackets rotate in under the bottom of the Wall Bracket as shown in the Detailed View of Diagram 11. Step 12: Insert the Safety Bolts (kk) into the threaded holes in the bottom of the Monitor Brackets (k, l) and tighten them with the Allen Key (ll) so that they sit behind the bottom tab on the Wall Bracket (c) as shown in the Detailed View of Diagram 12. Finally loosen the knobs on the Monitor Brackets and you are free to adjust your new flat panel TV. Etape 5 : Fixez les entretoises du support de fixation (i) au support de fixation (c) en plaçant les capuchons en plastique en face des trous ovales correspondants sur le support de fixation, tel qu'illustré sur la vue détaillée du schéma 5. [. . . ]