User manual SANSUI R-707L SERVICE MANUAL

[. . . ] € never pull the supply cord, or the appliance itself, to disconnect the plug from the electrical socket. ) • never let children or persons unfamiliar with the appliance use it without appropriate supervision. 13 Before doing any cleaning or maintenance work on the appliance, disconnect it from the supply mains, either by removing the plug from the socket, or by turning off the power at the mains. 14 If the glass surface of the cooktop cracks or breaks, disconnect the appliance immediately from the power supply. [. . . ] Important: the cooktop must be disconnected from the power supply before making any adjustments or performing any maintenance, etc. Installing built-in cooktops The cooktops have a type X protection rating against overheating in compliance with regulation CEI 335-2-6. Therefore, the cooktops cannot be installed alongside of cabinets which are higher than the surface of the cooktop itself. The following precautionary measures should be observed in order to ensure proper installation: a) Hoods must be installed in compliance with the required specifications contained in the instruction manual for the hood itself. B) The built-in ceramic glass top can be installed on any counter top as long as it is 600 mm or more in width and resistant to temperatures of up to 100°C. To remove the hob unit from its housing, undo the 2 Torx screws at the front, then the 2 Torx screws at the rear. REAR SPRING ASSEMBLY REAR LEFT MOUNTING REAR RIGHT MOUNTING 30 WORK SURFACE 40 FRONT OF THE HOB UNIT HOB UNIT FACE DOWN FRONT LEFT MOUNTING FRONT RIGHT MOUNTING SEAL MOUNTING FRONT / REAR RIGHT / LEFT MOUSSE 5x8 mm 48 10 51 0 Leave this much space between the bottom and the cabinetry 56 0+ /- 1 49 0+ /- 1 X (CEI 335-2-6) The aforementioned measurements must absolutely be observed in so far as improper installation can cause the surrounding surface areas to overheat. It is recommended that the cooktop be installed at a distance of at least 40 mm from the back wall or other vertical surfaces to ensure that the air circulates properly over the cooking area and to avoid overheating the surrounding surfaces. A seal or gasket is provided with the cooktop; make sure that it adheres properly to the bottom part of the frame of the cooktop. It is indispensable that the seal fits properly around the entire cooktop frame and especially along the corners in order to create a seal between the counter top and the cooktop itself so as to prevent spills or splashes from leaking into the cabinet below. Very important It is essential to instali the hob on a totally flat surtace. € To stop the audio signal, remove the object causing the interruption. € To reactivate the controls, follow the procedure for turning on the hob. And by two power level buttons : - + To turn on a heating zone and increase its power level, select the desired heating zone. To set a heating zone to maximum power immediately, press briefly on the "-" button. The Booster funtion is activated when the number 9 is replaced by "A". To turn off the heating zone, press on the "+" and "-" buttons at the same time. The power level is immediately set back to 0 and the heating zone is turned off. The heating zone's power level descends gradually until it is turned off. To turn off the entire hob simultaneously, press the button ; The entire hob is turned off. Models KT 6104 & 7104 only Functioning of the double heating zones Select the desired heating zone and press on the button corresponding to the extension (concentric or oval) to set the power level to its maximum. After selecting the power level, programme the cooking time as follows : • Press on the programming button 8. [. . . ] However, before cleaning, make sure that the cooktop has been turned off and is no longer hot. Stainless steel frame (only for specific models) Stainless steel can become spotted or discoloured if it remains in contact with water with high calcium levels, or with detergents that contain phosphorous. We recommend that the cooktop be rinsed with generous amounts of water and then dried after it has been cleaned. In addition, it is advisable to prevent water from spilling onto the surface. [. . . ]