User manual SAMSUNG NP700Z7CH

[. . . ] • Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your appliance. • Because these following operating instructions cover various models, the characteristics of your refrigerator may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or find help and information online at www. samsung. com. [. . . ] Insert the clip in the install pack and check that it holds the line firmly. 3. Make sure the hinge is level between the upper hinge hole 7 and the hole on the top of the cabinet 8 . Then, reattach hinge screws 9 and the ground screw 10 by turning it in a clock wise direction. Center of transparent coupler clip A (1/4”) (6. 35mm) Reattaching the Front Leg Cover Before attaching the cover, check water connector for leakage. Replace the front leg cover by turning the three screws clockwise, as shown in the figure. Place the front part of the upper hinge cover 11 on the front of the upper hinge 12 and reattach it with the screw. 12 11 10_ setting up DA99-02318A(0. 7). indd Sec4:10 2012. 2. 8 4:38:33 PM LEVELLING THE REFRIGERATOR Now that the doors are back on the refrigerator, you will want to make sure the refrigerator is level so you can then make final adjustments. If the refrigerator is not level, it will not be possible to get the doors perfectly even. The front of the refrigerator is also adjustable. MAKING MINOR ADJUSTMENTS TO THE DOORS Remember, a level refrigerator is necessary for getting the doors perfectly even. If you need help, review the previous section on levelling the refrigerator. When the door of the freezer is higher than the fridge 01 SETTING UP When the Freezer door is lower than the fridge Insert a flat-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to level the freezer. Adjustment part In the process for adjusting both the doors is the same. Unscrew the nut 1 from the lower hinge until it reaches the upper end of the bolt 2 . 3 1 Wrench 2 Nut Bolt Leg Screw Driver When the Freezer door is higher than the fridge Insert a flat-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to level the fridge. When you release the nut 1 , make sure that you use the Allen wrench provided 3 to loosen the bolt 2 in a counter-clockwise direction. Adjust the height difference between the doors by turning the bolt 2 clockwise or counter clockwise 3 2 Wrench Bolt . (Model with the purifier) - If you wish to reassemble the water inlet and outlet sides of the purifier during purifier installation, see the reference illustration. - Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap. setting up _13 DA99-02318A(0. 7). indd Sec4:13 2012. 2. 8 4:38:41 PM COUPLER “A” Remove any residual matter inside the purifier. (Model with the purifier) - Open the main water tap to check whether water is running through the water tube on the water inlet side of the purifier. - If water does not come out through the line, check whether the tap is open. - Leave the tap open until clean water is running out and any residual matter that built up during manufacturing has been removed. OUTLET SIDE OF PURIFIER PURIFIER TAP LINE OUTLET SIDE OF PURIFIER 90 degree CAUTION PURIFIER WATER Insert Locking Clip After tube seated WATER WATER INLET SIDE OF PURIFIER COUPLER Locking Clip WATER LINE Replacement Instructions 1. Insert water supply tube into the inlet side of the filter until the tube stop. FLOW DIRECTION Attach the purifier lock-clip. - Hold the purifier lock-clip in the appropriate position (under the sink for example) and fix it tightly into place where to screw. WATER SUPPLY INLET SIDE PERMEAT PURIFIER LOCK-CLIP Note : You must also ensure that the cut is square and not at any sort of angle as this could cause a leak Secure the purifier in position. - Fix the purifier in position, as shown in the figure on the right. WATER TUBE PURIFIER LOCK-CLIP PURIFIER 4. Flush filter for 5 minutes before use. 14_ setting up DA99-02318A(0. 7). indd Sec4:14 2012. 2. 8 4:38:42 PM Connect the water line to the refrigerator. - Remove the compressor cover of the refrigerator. - Reattach the compressor cover of the refrigerator. WATER LINE CONNECTION NUT Check the amount of water supplied to the ice tray. 1. When you press the Test button for 3 seconds, the ice cube container is filled with water from the water supply tap. Check to make sure the amount of water is correct (see the illustration below). This is a water pressure problem from with in the main water pipes, not the refrigerator. 1 01 SETTING UP INSTRUCTIONS COMPRESSOR COVER OF REFRIGERATOR Secure the water line. - Using clip ”A”, fix the water line to the wall (the back of refrigerator). [. . . ] After opening beyond a certain point, the door will “catch” and remain open. When the door is ajar ahead of the catch that allows it to stay open, it will close automatically. Cover filter 1 2 4 Sticker (month indicator) 3 5 Align the indication mark with lock position operating _21 DA99-02318A(0. 7). indd 섹션2:21 2012. 2. 8 4:38:48 PM troubleshooting PROBLEM SOLUTION • • • • Check that the power plug is properly connected. Is the temperature control on the display panel set to the correct temperature?Is the refrigerator in direct sunlight or located too near a heat source? [. . . ]