User manual SAMSON XML

[. . . ] Important Safety Information AVIS RISQUE DE CHOC ÉLECTRONIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. [. . . ] Moving 24 25 a slider in the positive direction will boost that frequency by as much as 12dB, and moving the slider in the negative direction will cut that frequency by up to 12dB. Once you set a response curve using the Graphic Equalizer, the EQ curve is applied to both the MAIN/MONO bus signal that is output to the speakers, and the line level signal which is output from the MAIN OUT jacks. MASTER - The MASTER level control is the overall volume control for the MAIN bus. The MAIN level affects both the MAIN bus signal, which is output to the speakers, and the line level signal which is output from the MAIN OUT jacks. 21 21 22 10 XML POWERED MIXERS Controls and Functions 26 27 28 26. EFX TO MON - The EFX TO MON control is used to adjust the level of the sound being sent back from the built-in digital effect to the MONITOR bus. Graphic Equalizer (XML610 and XML910 Only) - The 7-band Graphic Equalizer allows you to contour the frequency response of the MONITOR bus signal, providing a maximum of 12dB of cut/boost for each frequency band. This is an especially useful tool for cutting frequencies that cause annoying feedback. The frequency response is flat when the sliders are in the center position. Moving a slider in the positive direction will boost that frequency by as much as 12dB, and moving the slider in the negative direction will cut that frequency by up to 12dB. Once you set a frequency response curve using the Graphic Equalizer, the EQ curve is applied to both the MONITOR bus signal that is sent to the monitor speakers, and the line level signal which is sent from the MONITOR output jack. MASTER - The MASTER level control is the overall control for the MONITOR bus. The MONITOR level affects both the MONITOR bus signal which is sent to the monitor speakers and the line level signal which is sent from the MONITOR output jack. Owner's Manual XML POWERED MIXERS 11 Controls and Functions External Input Jacks (AUX IN and CD/TAPE IN) These input jacks allow the signal from an external device to be added to the MAIN output. AUX IN (XML410 Only) - This input jack allows the signal from an external device to be added to the MAIN output. 29 32 30 31 30. CD/TAPE IN - Use this stereo RCA input to connect a stereo output device such as an MP3 player or CD player to the mixer. TAPE IN VOLUME - The TAPE IN VOLUME is used to set the level of the CD/TAPE IN jacks. TAPE TO MON (XML610 and XML910 Only) - The TAPE TO MON switch allows you to add the CD/TAPE IN signal to the MONITOR bus. When you press this switch, the signal at the CD/TAPE IN is mixed in to the AUX 1/MON and the level is controlled by the TAPE IN VOLUME control. NOTE: When the TAPE TO MON button is in the down position, the TAPE IN VOLUME control is used to adjust the amount of signal that is sent from the CD/TAPE IN jacks to the MONITOR bus. 12 XML POWERED MIXERS Controls and Functions External Output Jacks The XML mixers feature several output connectors allowing you to interface a variety of external devices. A stereo recording device, such as a cassette recorder, can be connected to the REC OUT jacks, and additional power amplifiers can be connected to the MONITOR and MAIN output jacks. 34 35 36 33 33. REC OUT - The signal present at this stereo RCA connector is the MAIN bus signal before it has passed through the MASTER level control and graphic equalizer. This feature is convenient when connecting a microphone to CH 9/10 or 11/12 for making announcements and to use a footswitch to temporarily mute the music or input signals to CH 1-8. The signal is passed through the MONITOR/MASTER level control and graphic equalizer (XML610 and XML910) before it reaches the MONITOR connector. [. . . ] Follow the steps below to create an independent mix for the mount or speakers. 1. Set the channel MONITOR section and VOLUME control to the "0" position. Raise the AUX 1/MON controls for the channels that you wish to hear from the monitor speakers. NOTE: The MONITOR controls are not affected by the level settings of each channel. [. . . ]