User manual SAMPO SME-32HD5

[. . . ] HIGH DEFINITION DIGITAL TELEVISION 36" (34" Viewable) 16:9 PERFECTLY FLAT WIDE SCREEN 34" (32" Viewable) 4:3 SUPER FLAT TUBE 29" (27" Viewable) 4:3 SUPER FLAT TUBE USER MANUAL TABLE OF CONTENTS 1. FCC STATEMENT. . . . 8 5. USING THE TV'S ADVANCED FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15 6. USING THE MONITOR'S ADVANCED FEATURES. . . . 34-3 -1- FCC CLASS B STATEMENT IMPORTANT: The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Once pushed, the on-screen display will indicate the mute function is enabled. The on-screen display will disappear and sound will be restored from the speakers. BLUE BACK ON/OFF Push this button to enable/disable the blue back function. The blue back function is used to suppress "snowflakes" and audible noise when the television cannot receive a TV broadcast signal. DISPLAY Use DISPLAY button to show channel information on the screen. 15. WOOFER The built-in woofer can add a significant bass boost to the sound of your television/monitor. Each time the button is pressed, the on-screen display will display "woofer on" or "woofer off". 16. DEGAUSS Degaussing keeps the display free from unwanted magnetism that can result in color impurity. If the unit is displayed continuously, It is recommended that unit is degaussed at least once every few days to remove any color impurities. Whenever the degauss button is pushed, the display image blurs and a humming sound is heard. A minimum of 20 minutes should be observed between each use of the manual degauss button. -10- REMOTE CONTROL FUNCTIONS 17. V-CHIP V-CHIP (Parental Guide) This television is equipped with V-CHIP technology to prevent children from watching unsuitable programming. Press V-CHIP (blue) key on remote control to enter Parental Guide setting. Your television will display the following: Enter Parental code ----- 1 4 7 2 5 8 0 3 6 9 100 2. Press the following number keys on the remote control to enter the initial parental code: 8, 4, 8, 4, 100. After pressing the code, the screen will display "Parental Guide ON". to indicate the function is currently switched on. Parental Guide ON/OFF Set Page+ V-CHIP 3. Press V-CHIP (blue) key to go into the next menu to setup parental control settings. The following menu is displayed: Menu Code Reference Parental Guidelines Rating TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Set u u u u u u u u u u u u u u u u u u FV V S L D FV D L S V TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA : Fantasy Violence : Sexual Dialog : Adult Language : Sexual Situations : Violence : All Children : Older Children : General Audience :Guidance Suggested : Strongly Cautioned : Mature Audience Page+ -11- REMOTE CONTROL FUNCTIONS s 4. Use SET (red) key to t SET toggle between the U (unblock) setting or B (block) setting. Parental Guidelines Rating TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Set U U U B B B B B B B B B B B B B B U FV V S L D Page+ 5. V-CHIP Press V-CHIP (blue) key again to access the Motion Picture Association of America (MPAA) menu. The MPAA rating menu will display as follows: Menu Code Reference MPAA Movie G PG PG-13 R NC-17 X Set Rating Ratings U U U U U U Page+ G PG PG-13 R NC-17 X : General Audience : Parental Guidance : Strongly Cautioned : Restricted : No One Under 17 : No One Under 17 s 6. Use s(yellow) or t(green) keys to select the MPAA rating you wish to set. Use SET (red) t SET key to toggle between the U (unblock) setting or B (block) setting. MPAA Movie G PG PG-13 R NC-17 X Set Rating Ratings u u u B B B Page+ -12- REMOTE CONTROL FUNCTIONS 7. V-CHIP After the above setting is completed, press V-CHIP (blue) key to set the parental code. Set Parental code 2 5 8 0 1 4 7 3 8. 6 9 100 Enter a new passcode using the digit keys on the remote control. When you've completed entering the 5-digit code, press V-CHIP (blue) key to complete the process. [. . . ] ROTATION: Select icon to adjust the screen tilt of the displayed image. This is used to compensate for earth magnetic field effect on the monitor. This setting is available to TV/AV (Composite video AV1 & AV2), Y/CB/CR and Y/PB/PR signal inputs. This setting is available to TV/AV (Composite video AV1 & AV2), Y/CB/CR and Y/PB/PR signal inputs. [. . . ]