User manual SAMPO SME-32DL5

[. . . ] MULTIMEDIA MONITOR 34" (32" Viewable) 4:3 SUPER FLAT TUBE 29" (27" Viewable) 4:3 PERFECTLY FLAT TUBE USER MANUAL TABLE OF CONTENTS 1. 22 -3- WARNING AND CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR REAR) DO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE. HIGH VOLTAGE EXISTS ON THE CATHODE-RAY TUBE ANODE LEAD OF THIS MONITOR. BEFORE SERVICING, DETERMINE THE PRESENCE OF HIGH VOLTAGE BY CONNECTING THE H. V. [. . . ] 5. Connector type Horizontal size Vertical size 15 pin D-type and RCA JACK and 15 pin D-type and RCA JACK and S-terminal 9pin D-SUB S-terminal 9pin D-SUB 620 (for 465 (for +/- 8 mm RGB mode 1-9) +/- 8 mm RGB mode 1-9) 520 +/- 6 mm (for RGB mode 1-9) 388 +/- 6 mm (for RGB mode 1-9) - 10 - SPECIFICATIONS: MULTIMEDIA MONITOR 6. Unit dimension: W X H X D (mm) Packaging dimension : W X H X D (mm) Net weight of unit : User Controls: 34" (4:3) 866 X 718 X 583 1030 X 870 X 760 71 Kg 29" (4:3) 760 X 580 X 513 890 X 705 X 700 54 Kg 7. 8. Power, Brightness, Contrast, V-Size, V-Center, H-Width, H-Phase, Degauss, Pincushion, Trapezoid, Parallelogram, Rotation, R-Gain, G-Gain, B -Gain, Bass, Treble, Balance, Color, Tint, Sharpness, Mute, Volume, Woofer, Recall, Input Select, WIDE. 9. Operating temperature: 0J to 40J 10. Pin assignments for D-type connector Pin 1 : RED Pin 2 : GREEN Pin 3 : BLUE Pin 4 : GND Pin 5 : GND 11. The table below is required timings and technical description for the 34" tube (H=620mm, V=465mm standard size), 29" tube (H=520mm, V=388mm standard size). Y CB CR: This terminal is for Y CB CR signal and stereo sound signals, used with Y CB CR equipment. RS232 IN: This terminal is for control system signal, for use with IBM PCs and compatibles. (page 20) NOTE : 1. This terminal (AV OUT) only supply the AV1 or AV2 type signal and does not supply the Y CB CR type signal. AV AV3 L AV2 R- AUDIO- L OUT R- AUDIO- L L RS-232 RGB 1 IN AUDIO R L RGB OUT AC IN - - 12 - LOCATION OF BUTTONS ON REMOTE CONTROL POWER button (page 13) MUTE button (page 13) VOLUME+/- button (page 13) CHANNEL +/- button (page 20) INPUT SELECT button (page 20) 20 WIDE button (page 20) 20 DEGAUSS button (page 14) ?ADJUS button (page15 15) RECALL button (page 13) WOOFER button (page 13) INPUT DIRECTLY button INPUT DIRECTLY button (page 20) (page 20) Applicable Key Functions For monitor use POWERBMUTEBDEGAUSSBMENU+BMENU-BINPUT SELECT ADJ+BADJ-BVOLUME+BVOLUME-BWOOFERBRECALLBWIDE For tuner card use (OPTIONAL) MTS, CHANNEL+, CHANNEL-, CH ADD/ERASE, FULL SEARCH, CCD, BLUE BACK ON/OFF, AIR/CABLE, DISPLAY, 0~9, 100, QV, SET, t, s, V-CHIP NOTE: This remote control can be used for monitor and tuner card (OPTIONAL). - 13 - LOCATION OF CONTROL (ON FRONT PANEL) Front view 29" 3ADJUST4 RGB-2 IN CHANNEL INPUT SELECT DEGAUSS MENU VOL POWER/ POWER STANDBY SAVING POWER (page 20) (page 20) (page 14) (page 13/15) (page 13) 34" RGB-2 IN INPUT SELECT DEGAUSS MENU VOL STAND POWER POWER BY SAVING ADJUST NOTE: 1. RGB2 IN: This terminal is for RGB analog signal, use with IBM PC and other compatibles (except MAC PC). - 14 - INSTALLATION 1. Before you connect any cables, refer to the safety instructions at the beginning of this manual and make sure your computer (or video equipment) and display are switched off. Connect the video cable (AV, S-Video or RGB cable) and audio cable to your monitor. The power indicator should be illuminated. NOTE: If the button does not function due to interference, disconnect from the main power supply for 10 seconds. Then reconnect and turn the power on. AV1 R R- AUDIO- L Y CB CR R COMPONENT AUDI O LASER DISK or VCD or VCR RGB-2 IN AV AV3 L AV2 R- AUDIO- L OUT R- AUDIO- L L RS-232 RGB 1 IN AUDIO R L RGB OUT AC IN GAME PLAYER DVD PLAYER / SET TOP BOX PC/NOTEBOOK MONITOR 3ADJUST4 CHANNEL INPUT SELECT DEGAUSS MENU VOL STANDBY POWER POWERSAVING POWER - 15 - USING THE MONITOR' ADVANCED FEATURES S The " Digital Vision" feature advanced on screen adjustment for optimal viewing. To access the advanced features, open the access panel by pressing the center of the door on the set or use the remote control. POWER Press the power button, when the green LED (power) lights up, the power is ON. Press the button again, the green LED disappears and the red LED (stand by) lights up indicating that the power is OFF. The following audio functions are available only if speakers are attached. - VOLUME + Press and hold the Volume + button to increase the volume level. The Volume +/- button on front panel becomes ADJ +/- button, after the menu window appears on screen. MUTE R/C ONLY Use this button to quickly turn off the sound being heard through the speakers. (Once pushed, the on screen display will appear next to the button indicating that the mute function is enabled). To disable the mute function, simply press the button again, the On Screen Display will disappear and sound will be restored from the speakers. RECALL R/C ONLY Press this button to return the display to the factory pre-set default value. No recall item: RGB : Rotation Y PB PR: Rotation WOOFER R/C ONLY Press this button to switch the woofer ON or OFF. Each time the button is pressed, the on screen display will appear "woofer on", "woofer off" in turn. - 16 - USING THE MONITOR' ADVANCED FEATURES S DEGAUSS Each time you turn on your monitor it is automatically degaussed. Degaussing keeps the display free from unwanted magnetism that can result in color impurity. [. . . ] Contrast is the difference in brightness between the dark and light parts of the displayed image. Press the ADJ + button to increase contrast. - 20 - USING THE MONITOR' ADVANCED FEATURES S R B COLOR. Select this icon to adjust the tint of the displayed image. Press the ADJ + button to increase green. If PAL system in AV mode, and in PAL signal input, this icon will not work. SHARPNESS. [. . . ]