User manual SAITEK X-65F PRO FLIGHT COMBAT CONTROL SYSTEM

[. . . ] In order for this product to function correctly, please install the drivers on the CD supplied with this product. With your computer switched on, close down any programs that are currently running and insert the Installation CD into your CD-ROM drive. If the CD does not run automatically, select Start from the Windows® Taskbar, then Run and type D:\Setup. After reading the Disclaimer, select the I accept the terms of the Disclaimer option and click Next to continue. [. . . ] To move the axis curve, simply drag the arrow that is on the top of the X, Y and Rudder boxes; as you drag the arrow on the slider you will see the curve changing. If you wish to revert back to the standard axis envelope, simply right-click on the arrow and choose Clear Deadzone from the drop down list. You will also see the driver and software version that you have currently installed. From the About screen you can see notes on the programming software, which you may or may not have already installed. ST delivers a powerful set of features, allowing you to program your device with the ultimate configuration for total interaction. Despite a level of sophistication previously unseen in the market, and because of theSmart Technology inside, the software remains simple and intuitive to use. features of Smart Technology Programming Software: · Quick and easy setup in any game · Personalize the controller settings for your favorite games · Configure your controller with an on-screen high-resolution model and interface · Multiple setup options for each controller - ideal if a controller is used by several people · Program special moves with sophisticated timing features · Special game setups available as "Profiles" from the Saitek website and on the Smart Technology CD · Start the Smart Technology software, either:i) Click on Start, then All Programs, then look for Saitek SD6 Programming Software in your list of programs, click on this and under this heading you will see another heading with an icon saying Smart Technology. Ii) Look on your desktop for the Smart Technology icon, Once found, double-click and the Smart Technology software will load. Iii) Right-click the controller icon next to your clock, and then click the profile editor Once the ST software has opened, you will be presented with (if it's the first time you have run the software) a "tip" screen. these screens give useful information pertaining to the profile software. If you do not wish to see these screens when you start the ST software, un-check the small check box in the corner of the tip screen. The tip box can be closed by clicking on the OK icon in the bottom right corner. Once the tip box has shut down you will be presented with the main screen. On the Main screen you will see a series of tabs along the top, these are: - Product - Settings - Programming - Support The product page is the main screen that appears when the Smart Technology software is first opened. This screen detects which Pro Flight hardware you have plugged in and shows it on this screen. if you have no Pro Flight hardware plugged in , the Pro Flight Rudder Pedals will appear in the screen. Near the bottom center of the page there is a drop down selector box which allows you to alter the controller you wish to change the settings or programming for. In the settings tab you can alter the force settings for each of the 4 force sensing buttons, F1 to F4. This is done in a similar way to the Force tab in the Game Controller Settings. On the right side of the screen is the "Set Forces" area, this area allows you to set your force for each of the force sensing buttons. You will see 4 buttons, F1 to F4, these are the same buttons that are on your switch panel. You can then move the sliders, which are underneath the buttons, to your desired force. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected · Dans la fenêtre, sélectionnez Check this box to register now et suivez les instructions qui s'affichent à l'écran, vous pouvez aussi choisir de sélectionner cette option plus tard. Dans la fenêtre Registration, sélectionnez Check this box to register now et suivez les instructions qui s'affichent à l'écran, vous pouvez aussi choisir de ne pas sélectionner cette option et de vous enregistrer plus tard. Dans la fenêtre Registration, sélectionnez Check this box to register now et suivez les instructions qui s'affichent à l'écran, vous pouvez aussi choisir de sélectionner cette option plus tard. Dans la fenêtre Registration, sélectionnez Check this box to register now et suivez les instructions qui s'affichent à l'écran, vous pouvez aussi choisir de ne pas sélectionner cette option et de vous enregistrer plus tard. [. . . ]