User manual SAITEK CYBORG 3D STICK

[. . . ] The USB connector has many benefits over the older game port connector and is rapidly becoming the standard interface connection for quality computers. Important Notice: Connect your controller via only ONE of the above methods. Important Notice: If you connect the Cyborg 3D Stick, using the USB connector, before installing the Saitek Gaming Extensions software, the Saitek Cyborg 3D Stick will not function correctly. To solve this problem, run the NukeUSB utility (found on the Saitek Product Companion Disc CD) to remove the Cyborg 3D Stick from the Registry, restart the machine and then continue the installation as detailed above. [. . . ] If you are prompted to install Microsoft® DirectX 7. 0a, click on Install and follow the on-screen instructions and then restart your computer when prompted. · 1 Figure 2 - Head / Palm Rest Adjustments Adjustment pin for head tilt Adjustment screw for head roll Tilt adjustment plate Adjustment screw for palm rest Figure 1 - Cyborg Controls 8 Way Hat Fire Button C Fire Button B Fire Button A Trigger Throttle Right Shift Button F2 Button F4 Button F1 Button F3 Button Left Shift Button Adjustment screw for throttle Figure 3 - Cyborg Throttle Adjustment Adjustment screw for throttle Saitek adjustable tool 2 3 Adjusting the stick for left handed use Thumb length adjustment The control head has three tilt positions, these are adjusted by a three position spring loaded pin located on the left side of the joystick, above the main trigger (see figure 5). Fig. 5 Sprung locator pin, push inwards using the Saitek Adjustment Tool Alternative location holes L L L L L Using the Saitek Adjustment Tool (1), remove the screw situated in the middle of the main palm rest section Pull the flat hand rest out of its slot in the main palm rest section (2), and turn the hand rest over (3) Push the hand rest lug back into the slot in the palm rest section but from the other direction, so it is now on the left-hand side. Align the locating lug on the palm rest with the desired hole on the handle (the right-hand column of holes), and gently push the palm rest back onto the joystick. Replace the screw, and tighten using the adjustment tool (4) L L L Using the Saitek Adjustment Tool push the locator pin inwards, until it has cleared the hole in the tilt adjustment plate (see figure 5). Tilt the joystick head until the locator pin isn't sitting under a hole, and remove the adjustment tool from the locator pinhole. The pin is sprung, so it will automatically locate into a new hole, once positioned correctly. Repeat for all positions, until you find the position, which meets your preference. Hand size adjustments L Head Roll Angle (Left/Right) Adjustment Fig. 6 Fig. 7 L L The palm rest height can be adjusted, making the stick fit your hand perfectly. Follow points 1and 2 from the previous section, refitting the palm rest to the height that best suits your hand size. Repositioning the Throttle Control The control head has three roll positions, which can be set using the roll adjustment screw at the front of the control head (see figures 6 and 7): The throttle control can also be adjusted to suit left-handed use. L L Using the adjustment tool remove the screws on either side of the throttle control. Swap the throttle handle and the cover over, and replace the screws in each side. L L Using the adjustment tool unscrew the head roll adjustment screw by 3 complete turns. Once loosened off, push the head towards the back of the joystick (towards the throttle). The roll-locating pin (see figure 6) will now move out of its current position, allowing the head to be rolled either left or right. The locator pin is in the middle of the control head, above the main trigger. This pin can sit in three positions between locating lugs, also visible by the locating lug. 4 5 L Roll the head, so that the locating pin is between two of these lugs, and pull the control head back towards the front of the stick. [. . . ] THEREFORE, IF YOU MAKE A MISTAKE, SIMPLY HIGHLIGHT THE COMMAND LINE AND TYPE IN THE CORRECT ENTRY. For a full guide to programming your Saitek Cyborg 3D Stick with SGE, see the Saitek Gaming Extensions: User Manual supplied on the Saitek Product Companion CD that came with this product. Technical Support The Saitek Website If you have access to an Internet connection, many of your technical queries may be answered with a simple visit to the Saitek Website at: http://www. saitek. com The technical support area will provide you with all the information you need to get the most out of your controller, solve any problems you might have and provide you with the latest game configurations. [. . . ]