User manual SAECO BP 36

[. . . ] Warning Timetable management Besides the ALWAYS FREE and NEVER FREE functions, this menu also allows to enter time periods in which the selected beverages are supplied either FREE of charge or with the two DIFFERENTIATED PRICES (example: FREE - Monday ­ ON=20:00 ­ OFF=24:00. Selections will be free every Monday during the time period 20:00 to 24:00). The DIFFERENTIATED PRICES 1 and 2 (linked to each selection) may be entered in the same way. In addition, it is possible to set the timetable for turning the device on and off. Connect the clock module in such a way that reference A (on its back) aligns with reference B, which is to be found on the base of the connector. Warning B A The time periods for the same function must NOT overlap. System management In this menu it is possible to access the CLOCK function, which allows you to enter the hour, minutes, month and year. [. . . ] 2 nm >00000< FREE VEND nm >00000< Espresso Italia PTY LTD www. espressoitalia. com. au 5 Freecall 1300 660 976 English 2. 2 Programming key Maintenance Technician This operation should be carried out by the Maintenance Technician. The programming key allows to transfer the data entered into the following sections of the programming menu: - SALES MANAGEMENT. " It is possible to transfer all the data, with the exception of the code of the SERIAL NUMBER and of the PASSWORD. When the device is next turned on, the display will show the message: "TRANSFER KEY - RIGHT MODEL", if the key connected corresponds to the vending machine model (example A), or "TRANSFER KEY - WRONG MODEL", if the key connected does not correspond to the vending machine model (example B). In case A, it is possible to transfer the parameters from the vending machine to the programming key and vice-versa. A DATA TRANSFER SAVING DATA TRANSFER KEY RIGHT MODEL DATA TRANSFER KEY -> VMC DATA TRANSFER READING DATA DATA TRANSFER VMC -> KEY DATA TRANSFER WRITING DATA The connector (10 - Fig. To connect up the programming key, proceed as follows: - open the front door of the vending machine; - slide out the nation key from the connector (10 ­ Fig. 1); - connect up the programming key to the same connector as the nation key (Fig. 3). In case B, it is only possible to transfer the parameters from the vending machine to the programming key. B TRANSFER KEY WRONG MODEL DATA TRANSFER VMC -> KEY DATA TRANSFER WRITING DATA NOTE To go back to the previous menus, press the back to the previous levels, press the key. key; to go Any errors that may occur during the data transfer phase are displayed with the message "TRANSFER KEY - ERROR IN KEY DATA". Should this message appear, repeat the data transfer procedure; if the error continues to appear, contact an AUTHORISED CUSTOMER SERVICE CENTRE. Important When the data transfer has been completed, reinsert the nation key as per the instructions given in the operation and maintenance manual for the automatic vending machine BP 56 e BP 36. Fig. 3 6 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 3 3. 1 PAYMENT SYSTEMS Installing the SAECO CARD Maintenance Technician - apply the antenna (B ­ Fig. 6); This operation should be carried out by the Maintenance Technician. 4) A 1 universal module; B 1 antenna; C biadhesive plate; D protective linen band; E 1 adhesive label for the reading position of the SAECO CARD; F flat cable. Fig. 4 Installation Before installing, make sure that the TIME KEEPER clock module is fitted (point 2. 1). Then, proceed as follows: - open the front door of the vending machine; apply the biadhesive plate (C ­ Fig. 5 Espresso Italia PTY LTD www. espressoitalia. com. au 7 Freecall 1300 660 976 English - On the BP 56 position the universal module (A ­ Fig. 9a 8 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English - On the BP 56 connect the far end of the flat cable (F ­ Fig. 10 Important - On the BP 36 connect the far end of the flat cable (F ­ Fig. 10a); The label indicates the area in which the SAECO CARD is positioned. 3. 1. 1 Functions of the SAECO CARD in the programming menus Sales management This menu allows to access the SAECO CARD DISCOUNT function, where the discount value can be entered. This discount is applied to users who purchase products with the SAECO CARD system. In order to change the value, press ; a luminous cursor appears and, by using the and/or keys, it is possible to change the setting. Fig. 10a Payment system This menu allows you to access the following function: MAX CARD CHARGE. [. . . ] 19 position the panel that supports the banknote reader at the same point as the panel that has just been removed (Fig. 20 re-attach the upper panel of the keyboard and reconnect the cable to the connector (Fig. 23 Espresso Italia PTY LTD www. espressoitalia. com. au 13 Freecall 1300 660 976 English - connect the BANKNOTE READER cable to the connector (1 ­ Fig. 24); Important The programming procedures are shown in the operation and maintenance manual for the automatic vending machine BP 56 e BP 36. [. . . ]