User manual RYOBI TSC306 SCHEMA ELECTRIC

[. . . ] Do not restore power until the installation is complete. ~ Do not modify the plug provided ~ Do not use an extension cord to ~ This dryer must be vented outdoors ~ Use flexible or rigid metal pipe for ~ Before installation, disconnect the venting. Non-metallic flexible hose should not be used, it is a potential fire hazard. ~ GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. [. . . ] ~ If there is any doubt concerning installation, contact Miele's Technical Service Department. U V 1-800-999-1360 techserv@mieleusa. com 1-800-565-6435 service@miele. ca 6 Installation Front view a Exhaust connection b Power cord with plug c Control panel d Door e Four height adjustable screw feet Stand A dryer stand, with drawer, can be purchased as an optional accessory. 7 Installation Rear a Handle for transportation (arrows) b Power cord with plug c Slot for module d Air intake e Gas connection f Vent connection with restriction insert 8 , WARNING Do not remove the restriction insert in the vent opening. It may result in poor drying results, damage to the laundry and higher Carbon monoxide emissions. Installation site , WARNING: Do not install the dryer: - outdoors - in an environment with dripping water or weather - near flammable materials - in rooms which may contain gas or other fuels - in closets with solid doors - with other fuel-burning appliances in the same closet - in a location where its door could conflict with room doors. - next to a refrigerator - under a countertop - on top of a washer. , The National Fuel Gas Code restricts installations of gas appliances in garages. They must be 18 inches off the ground and protected by a barrier from vehicles. 9 Installation site Confined space installation ^ When installed in any space with less than 122 square feet, minimum clearances around the dryer must be adhered to for proper ventilation and vents for make up air must be installed. ^ Do not install any other fuel-burning appliance in the same space as the dryer. Confined door openings Any doors limiting circulation must be louvered or otherwise ventilated. It must be equally divided within 12" (30. 5 cm) from the top and bottom of the door. Minimum installation clearance Sides: 0 " (0 cm) Top: 12" (30. 5 cm) Rear: 0" (0 cm) (as close to wall as gas connection and venting allows) Front to door: 2" (5 cm) Make sure the dryer door can open completely once installed. Exhaust duct clearance to combustible material: 2" (5 cm) 10 Installation Transporting the dryer to the installation site The rear of the lid has a handle for transportation. ^ Use the front dryer feet and the rear of the lid to move the dryer to the installation site. Level the dryer The dryer must be level to ensure safe and proper operation. ^ Unscrew the four feet as necessary by turning the foot, 1, and the locking ring, 2, to the left. At the same time, turn the locking ring, 2, to the right using another wrench. , The dryer lid cannot be removed. 11 Installation , WARNING Before installation, disconnect the tumble dryer from the electrical supply by shutting off the power main or tripping the circuit breaker. An 1/8" NPT pressure tapping plug must be installed immediately upstream of the gas supply connection. This allows the gas inlet pressure to be checked. 15 Gas connection , To secure all connections use appropriate Teflon tape or a thread compound, suitable for gas connections. ^ Install a 3/8" flare union adapter, a, to the female elbow, b. Hold the elbow with a wrench. ^ At the end of the dryer's gas connection hand screw on the 3 /8" NPT elbow. Using a wrench tighten the elbow with a half turn. , DO NOT OVERTIGHTEN. ^ Secure the flexible metal gas line connector to the adapter. 16 Gas connection ^ Using two wrenches tighten the flexible gas line connection. ^ Using two wrenches tighten all connections. , DO NOT OVERTIGHTEN. ^ Connect the flare union adapter, a, to the pressure tapping plug, b, originally installed on the gas shut off valve, c. ^ Open the gas shut-off valve. ^ After connecting the appliance check all fittings for gas leaks e. g. with soapy water or an equivalent. , WARNING NEVER USE AN OPEN FLAME TO TEST FOR GAS LEAKS. 17 Ducting Exhaust ducting and connections A gap of 3/8" (10 mm) must be provided between the machine and the floor. This gap is necessary for proper air flow and must not be blocked by a toe-kick or thick piled carpets. Sufficient venting of the installation site is essential for proper dryer operation. Inadequate ventilation will increase energy use and drying times. , WARNING Danger of toxic fumes. The exhaust gases from the dryer must only be vented outside the building. DO NOT terminate the exhaust ducts in a chimney, fireplace ducting, a combustion appliance vent flue, or enclosed, unventilated area such as attics, garages, crawlspaces, walls, ceilings or concealed space of a building. [. . . ] Establish the number of elbows or bends necessary, noting the type of bend, angle and radius involved (see Table). Add the additional duct length (as derived by using the values specified in the table) to the actual duct length to get the effective length. Tips about the ductwork ­ Check with your local building code to determine the maximum allowable duct length. Flexible foil ducting may move and bounce due to the high airflow of the dryer. ­ For best drying results avoid extra long ducting with too many bends, angles or tight corners. [. . . ]