User manual RYOBI TFD220I SCHEMA ELECTRIC

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RYOBI TFD220I. We hope that this RYOBI TFD220I user guide will be useful to you.


RYOBI TFD220I SCHEMA ELECTRIC: Download the complete user guide (26 Ko)

Manual abstract: user guide RYOBI TFD220ISCHEMA ELECTRIC

Detailed instructions for use are in the User's Guide.

[. . . ] ­ items that have been previously cleaned, washed, soaked or spotted with gasoline, dry-cleaning solvents or other flammable or explosive substances. ­ items treated with flammable cleaning agents or items containing acetone, alcohol, petrol, stain remover, wax or chemicals from buffing, etc. ­ items which have been splashed with hair spray, nail polish remover, etc. When washing heavily soiled items ensure that sufficient detergent is used with a high temperature. [. . . ] Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. See "Frequently asked questions" for details. ^ Press the "Door" button. ^ Close the door. ^ Press the "On/Off" button to turn off the dryer. ^ Empty the condensed water container weekly (if not connected to a drain). 11 Using the dryer Canceling or changing a program ^ Press and release the "Start/Stop" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the dryer. They will damage the surface. ^ Take the door lint filters out by turning the knob at the filter top. Lock the door frame filters. ^ The exterior and the control panel can be cleaned with warm water and liquid dish soap applied with a soft sponge. ^ Wipe dry. Cleaning the drum ^ The stainless steel surfaces of the drum can be cleaned using a non-abrasive stainless steel cleaner. ^ Wipe clean with a soft cloth. 15 Dryer care Emptying the condensed water container Depending on the installation, the condensed water will either be pumped to a drain or collected in the condensed water container, located in the upper left corner of the machine. Should the container be full when the tumble dryer is started, or if it becomes full during normal operation: ­ The "Container" indicator will light. The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is ^ Restore power. securely closed to prevent a short circuit or penetrating moisture. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^ Flip down the bulb cover. 19 Frequently asked questions What if the dryer will not run?Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. Solution See "Changing the light bulb. " Solution Make sure the dryer is on. Close the door properly. What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started?See "Child Lock. " What if the program stops, the "End/Anti-crease" indicator lights and the buzzer sounds?Single items should be dried with "Sturdy" or a timed program and dry items in the "Fluff" program. 20 Frequently asked questions What if the "Filter/Vent" fault indicator is lit?Open a window or door to increase airflow. What if the program runs too long or stops?Clean the lint filters (see "Dryer care"). The laundry was not spun sufficiently in Select a higher spin speed in the wash the washer. Possible fault The load contained too many dissimilar items (size and fabric. ) What if water has collected around the drum opening?Remove any blockages. 21 After sales service Repairs In the event of a fault which you cannot fix yourself, please contact Miele's Technical Service Dept. [. . . ] The electrical connection should be near the dryer and accessible at all times. Extended machine feet* are recommended at a built-in height of more than 33 1/16" (840 mm). Remove the original machine feet and replace them with the extended ones. One or two filler frames* are recommended at a niche height of 34 1/4" / 34 13/16" to 36" / 36 5/8" (870/885 - 915/930 mm). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RYOBI TFD220I




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RYOBI TFD220I will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.