User manual RYOBI TFD170I SCHEMA ELECTRIC

[. . . ] ­ items that have been previously cleaned, washed, soaked or spotted with gasoline, dry-cleaning solvents or other flammable or explosive substances. ­ items treated with flammable cleaning agents or items containing acetone, alcohol, petrol, stain remover, wax or chemicals from buffing, etc. ­ items which have been splashed with hair spray, nail polish remover, etc. When washing heavily soiled items ensure that sufficient detergent is used with a high temperature. [. . . ] ^ Wipe dry. 16 Dryer care Changing the light bulb ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place. , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is ^ Restore power. securely closed to prevent a short circuit or penetrating moisture. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^ Flip down the bulb cover. 17 Frequently asked questions What if the dryer will not run?Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. Close the door properly. The bulb may be bad or burned See "Changing the light bulb. " out. What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started?See "Child Lock. " What if the program stops, the "Anti-crease / End" indicator lights and the buzzer sounds?Single items should be dried with "Sturdy" or a timed program. For dry items use the "Fluff" program. What if the "Filter/Vent" fault indicator is lit?At the end of a program The "Anti-crease / End" indicator will light. ^ Press the "On/Off" button to turn off the dryer. ^ Press the selection button until the desired indicator illuminates. Quick Guide Program Normal Extra Dry When to use For laundry to be folded and shelved immediately, e. g. For items to be left damp for ironing. Note The "Extra Dry" program should not be selected for jersey materials. Items may shrink. Available drying options: Turbo, Full load, Gentle, Anti-crease More Dry Normal Less Dry Hand Iron Rotary Iron If items are still damp, dry again using "More Dry". If fabrics are too damp, dry again using "Less Dry". For items to be ironed with a rotary iron. For items which require ironing. To prevent moisture loss, roll up the laundry until ready to iron. Wrinkle-free Available drying options: Turbo, Gentle, Anti-crease More Dry Normal Less Dry Reduce load size for fabrics that wrinkle easily. Special Programs Available drying options: Anti-crease only available in Fluff, Sturdy Woolens Delicate items which allow machine drying. Take items out immediately after the end of the program while still slightly damp. Allow items to air dry. Smooth Sturdy Fluff - TIMED CYCLES Available drying options: Gentle, Anti-crease 20 min 45 min - Installation Instructions To prevent accidents and appliance damage read these instructions before installation or use. IMPORTANT SAFETY INSTRUCTIONS , WARNING - Risk of Fire death, follow all installation instructions. ~ To reduce the risk of severe injury or ~ WARNING ­ Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the appliance is properly grounded. ~ Clothes dryer installation must be performed by a qualified installer. ~ Install the clothes dryer according to the manufacturer's instructions and local codes. ~ Repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty. [. . . ] Otherwise drying times and energy consumption may increase. 30 Installation Exhaust connection Using the connector supplied, an exhaust hose (4" [100 mm] diameter) can be installed. Necessary materials: ­ a wall or window duct (available from Miele) ­ an exhaust hose/pipe made of approved non-flammable material Window connection 1 Window duct ( (installed in a "plexiglass" pane) 2 Connector for the flexible metal exhaust hose Wall connection with rigid pipe ^ Install the exhaust hose/pipe, 2, with the connector, 1, to the dryer. 1 Wall pipe (Installation sheet supplied with the Miele wall pipe) 2 Connector 3 Rigid pipe 31 Installation Direct wall connection Necessary materials: ­ a wall pipe ­ flexible foam gasket Dryer top view Dryer side view 1 Wall pipe 2 Flexible foam gasket 1 Wall pipe 2 Flexible foam gasket ^ Connect the flexible foam gasket, 2, to the wall pipe connector, 1. ^ Push the dryer to the wall. 32 Installation How to calculate the effective duct length The overall duct length will determine the duct diameter (see the "Additional duct lengths" table). ^ Measure the actual duct length needed to go from the dryer's exhaust connection to the vent outlet: 1. [. . . ]