User manual RYOBI SP1800I SCHEMA ELECTRIC

[. . . ] Before this appliance is removed for service or discarded, remove the door to the drying compartment. Do not install or store this appliance where it will be exposed to the weather. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in these operating instructions. Repairs to electrical appliances should only be performed by qualified personnel. [. . . ] Select the dryness level The dryness level can be selected in the "Normal" and "Wrinkle-free" programs. Select the buzzer (if desired) ^ Press the "Buzzer" button to have a tone beep at the end of the program. Indicator light: on = buzzer selected off = buzzer not selected Adjusting the buzzer volume: ­ the dryer must be on ­ the door closed ­ a program selected ­ if the "Buzzer" indicator is lit, press the "Buzzer" button so its indicator light goes out. In the "Wrinkle-free" program, only "More Dry", "Normal" and "Less Dry" can be selected. ^ Press and hold the "Buzzer" button until its indicator lights and you hear the desired volume and tone. 10 Using the dryer 6. At the end of a program The "Anti-crease/End" indicator will light at the end of a program and the buzzer will sound if it was selected. Once the program starts, the current cycle of the program will be indicated in the "STATUS" display. See "Frequently asked questions" for details. ^ Press the "Door" button. ^ Close the door. ^ Press the "On/Off" button to turn off the dryer. ^ Empty the condensed water container weekly (if not connected to a drain). 11 Using the dryer Canceling or changing a program ^ Press and release the "Start/Stop T" button to stop the drying program. To continue drying: ^ Select the new program by pressing the e or - button. ^ To prevent leaks, make certain the condenser is pushed in all the way and locked in place. ^ Restore power. ^ Rinse the condenser along the left side with warm water. ^ Rinse the condenser from the front with warm water. ^ Place the condenser lengthwise on a towel to air dry. 18 Dryer care Changing the light bulb ^ Replace the light bulb with a temperature proof bulb, available from Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Flip up the light bulb cover and press it firmly until it clicks into place. , To reduce the risk of electric shock, disconnect the dryer from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before performing maintenance. ^ Open the door. The bulb cover is located along the upper rim of the drum opening. , Make sure the bulb cover is securely closed to prevent a short circuit or penetrating moisture. ^ Restore power. ^ Slide a screwdriver with a wide head underneath the side edge of the bulb cover and twist (see illustration). ^ Flip down the bulb cover. 19 Frequently asked questions What if the dryer will not run?Add fabric softener to laundry when washing or select the "Less Dry" setting on the dryer. Fix See "Changing the light bulb. " Fix Make sure the dryer is on. Close the door properly. What if the "Child Lock" indicator flashes after turning the dryer on and a program cannot be started? [. . . ] are disposed of safely and kept out of the reach of children. Disposal of an appliance Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. While being stored for disposal remove the door to the drying compartment. 25 Washer / Dryer Stack The tumble dryer can also be placed on top of a Miele washing machine for a stacked installation. The stacking kit is available from your Miele dealer or the Miele Technical Service Department. , Installation of the stacking kit must be performed by a Miele authorized technician. Height of a stacked installation 5' 6 3/8" (168. 6 cm) (Stacking kit with a pull out shelf) 26 Electrical connection GROUNDING INSTRUCTIONS This appliance must be grounded. [. . . ]