User manual RYOBI RYOBI 30120

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RYOBI RYOBI 30120. We hope that this RYOBI RYOBI 30120 user guide will be useful to you.


RYOBI RYOBI 30120 : Download the complete user guide (2271 Ko)

Manual abstract: user guide RYOBI RYOBI 30120

Detailed instructions for use are in the User's Guide.

[. . . ] OWNER’S MANUAL acknowledgement MODEL PT-35 POWER TILT & TRIM COOK COOK MANUFACTURING CORPORATION 3920 SOUTH 13TH • DUNCAN, OKLAHOMA 73533 (580) 252-1699 MANUFACTURING CORPORATION © COPYRIGHT - 2006 Part #52160 REVISION 5 FOREWORD Thank you for choosing a CMC product. This manual is designed to aid in installation and maintenance of your PT-35 Power Tilt and Trim. Each part of the CMC PT-35 is machined from the highest quality material to ensure many years of trouble free service. Computer aided design and precision machining of the PT-35 is done totally at our facility, so you can be sure you have purchased the best quality unit on the market. LIMITED WARRANTY New CMC PT-35 Power Tilt & Trim units are warranted by the manufacturer for one year from date of purchase against defects in workmanship and/or materials in the hydraulic system and five years from the date of purchase against defects in workmanship and/or material in the structure. [. . . ] Position the switch so the terminal posts are on the side nearest you. Step 13: Push the toggle switch through the 1/2 inch hole that you previously drilled. Place the updown switch plate and rubber boot with nut on the switch (Fig. Step 14: Connect the 2-wire male connector from the hydraulic power unit to the female 2-wire connector at the end of the wire assembly (Fig. NOTE: If your boat is used in a corrosive environment such as saltwater and you cannot locate a dry place for the relays, you can secure the relays inside the cowling of your engine. Instead of connecting the positive and negative ring terminals of the wire assembly to the battery, connect them to the starter where the positive and negative leads from the battery are attached. Step 15: Connect the ring terminal labeled POS to the positive battery terminal and connect the ring terminal labeled NEG to the negative battery terminal. CAUTION: WHEN TRAILERING IT IS RECOMMENDED TO SUPPORT THE PT-35 WITH A TRANSOM SAVER DEVICE. WHEN RUNNING THE PT-35 DOWN TO THE SUPPORT, JUST MAKE CONTACT WITH IT. DO NOT CONTINUE TO LUG IT DOWN AFTER INITIAL CONTACT HAS BEEN MADE OR DAMAGE TO THE, PT-35 WILL OCCUR. Fig. All of the mounting bolts should be checked for tightness frequently. SERVICING Your CMC PT-35 is operated with a hydraulic actuator, which is located inside the unit. It is filled with the correct amount of hydraulic fluid and tested at the factory. If it becomes necessary to add fluid to the actuator, use #2216 Mystic or equivalent, SAE 20 or 30 non-detergent oil. Follow the procedure below for adding fluid and bleeding the system: First, trim the PT-35 all of the way down. Remove the 1/8" brass socket filler plug with a 3/16" hex key wrench (Fig. You can access this plug through the lower machined hole on the port side motor rail as shown in Fig. Pour fluid into the actuator through the filler hole until fluid runs out of the level hole on the side of the actuator (Fig. Run the actuator until the ram is fully extended and the motor bogs down (the PT-35 is all the way up). Then retract the ram completely until the motor bogs down (trim the PT-35 all the way down). Tilt the PT-35 out until the ram is extended 2 to 3 inches out of the actuator (Fig. If preferred, the above procedure can be executed with the actuator completely remove from the PT-35. Please see the next page for the removal of the actuator. CONNECTING TO POWER SOURCE Step 11: Find a good location for the up-down toggle switch. [. . . ] This warranty means that only the parts that prove defective during the period of warranty will be repaired or replaced at our option. Cook Manufacturing Corporation will accept only parts returned for warranty prepaid from initial purchaser and return the repaired or replaced parts freight collect. Avoid tampering with the Hydraulic Actuator, if a warranty claim is to be made. The warranty is void on any hydraulic actuator returned that shows signs that it has been dismantled or electrical cordset from the motor has been cut. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RYOBI RYOBI 30120




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RYOBI RYOBI 30120 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.