User manual RYOBI RHP1150 AM SCHEMA ELECTRIC

[. . . ] For installation of the cover, a minimum distance of 20" (510 mm) is required between the countertop and wall cabinetry. Note: The wok/pan support should be removed before lowering the stainless steel cover (EA 80). j Ignition safety control k Burner base l Control for burner m Control panel Do not install the Da 8-2 directly next to the gas hob. 3 Contents Contents Description of the appliance . 17 For the installer / electrician / engineer ]ö Electrical connection . 37 For your safety For your safety WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. [. . . ] Clean the cooktop surface using hot water with a little dishwashing liquid. Clean the control knob and the control panel with hot water and a little dishwashing liquid. A proprietary cleaning agent for stainless steel can be used on the stainless steel cooktop surface. Control panel / Control knob Do not use any scouring agents or pads on the knob or control panel, as these could cause damage. Under no circumstances use a steam-cleaning appliance to clean the gas cooktop. The steam could penetrate to live components and cause a short circuit. 15 Problem solving guide Problem solving guide Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified person. However some minor problems can be resolved as follows: What to do if . Check whether: the large burner cap and the large burner cap base are correctly positioned. Check whether the burner caps and large burner cap base are correctly positioned. Check whether the large burner cap and the large burner cap base are correctly positioned. Check for food residues covering the tip of the ignition safety control. Check, whether the orifices of the small burner cap are clean, especially those toward the tip of the ignition safety control. Follow the procedure on how to start the flame from top left of page 11, do not forget to depress the knob to the bottom before releasing after 5­10 seconds. For convenience, an approved type of flexible stainless steel gas pipe (accordion type) may be installed between the adapter and the regulator. If an elbow adapter is necessary for your particular installation, a customized one ­ can be obtained free of charge from the Miele parts department (USA). Do not use any regulator or adapter, straight, elbow or otherwise, unless it has been supplied by Miele Appliances. Should you have any questions, please call the Miele Service Department at USA: 1-800-843-7231 CDN: (905) 474-1073 or -9191 ext. 234. A straight thread adapter, from 1/2" ISO 7-1 to 1/2" NPT is included with the appliance. (Elbow adapter is also included for appliances sold in Canada. ) As shown in the above diagram, the included adapter and regulator must be used when connecting the Miele cooktop. These two items have been customized by Miele to meet all applicable safety requirements. 20 Gas connection Pressure regulator A pressure regulator convertible to Natural and LP Gas (Liquefied Petroleum) is included with the appliance. Conversion is carried out by inverting the regulator cap marked "NAT"/"LP". If "NAT" is visible then the regulator is set for Natural gas and if "LP" is visible then it is set for Liquefied Petroleum Gas. 0. 2 kW 680 Btu/h For USA only The gas connection must be made in accordance with local codes, or in absence of local codes, with the National Fuel Gas Code, ANSI Z 223. 1. Supply Pressure: 1/2 PSI Manifold pressure: ­ Natural gas 4" water column ­ Propane gas 10" water column Min. [. . . ] Screw the three screws into the burner base using a suitable philipeshead screwdriver. Put the large burner cap base, the burner ring, the large burner cap and the wok/pan support in place. Check that the tab of the large burner cap is correctly positioned in the notch of the base and that the lug of the base is correctly positioned in the notch of the housing. When set at "low", or when the control knob is quickly turned from "high" to "low" the flame should not go out. [. . . ]