User manual RYOBI RHP1120 SCHEMA ELECTRIC

[. . . ] Caution: Do not store items of interest to children in cabinets above the appliance. Children climbing on the appliance to reach these items could be injured. Keep children away from the appliance. ~ The appliance is hot during use and ~ Keep all pots and pans out of the ~ Pot and pan handles should be Correct usage ~ Only use the cooktop for residential cooking, and for the purposes described in this manual. ~ Persons who lack physical, sensory or mental abilities, or experience with the appliance should not use it without supervision or instruction by a responsible person. reach of children. [. . . ] ­ Use little water when cooking and take care to select a lower energy level as soon as cooking is completed. ­ For longer cooking periods, you can switch off the cooking zone 5 to 10 minutes before the total cooking time is completed. The residual heat will continue to cook the food. 20 Timer The cooktop must be turned on to use the timer. The timer can be used for two different functions: ­ To time kitchen activities ­ To set a burner to turn off automatically. Example: With a time of more than 99 minutes, the timer must be turned to hours. Example (2 hours 30 minutes): h When the set time has elapsed, 00 will appear in the timer display and an audio signal will sound for a few seconds. 21 Timer Setting the timer Minutes Example: You want to set a time of 15 minutes. Hours To set full hours, touch the respective number on the settings bar. To set the half hours, touch the space between 2 numbers on the settings bar. 00 appears in the timer display, and the right 0 will flash. h ^ Touch the first number of the time you wish to set (in this case 1) on the settings bar. The timer display changes, 1 flashes on the right. h ^ Touch the h control to switch the display to hours. h ^ Touch the second number (in this case 5) on the settings bar. The timer display changes, the 1 "jumps" to the left and 5 appears on the right. h ^ Touch the settings bar between the numbers 2 and 3. h After several seconds, the m touch control and the timer display stop flashing and turn steady. The burner power-levels and the timer setting cannot be changed, the cooktop can only be turned off. When Stop and Go is deactivated, the cooking zones resume at the power level which was last set. If Stop and Go is not deactivated, the cooktop turns off after 1 hour. When Stop and Go is activated: - the timer will continue without interruption - the countdown of a time programmed for automatic shut-off will be interrupted, When deactivated the countdown time will continue to run. The burners will now run at the power level that was previously set. 27 Safety features Safety shut-off Safety shut-off for cooking times that are too long If a burner is heated for an unusually long period of time (see chart) at the same power level, the cooktop will turn itself off automatically and the residual heat indicator will appear. To use the burner again, turn it back on in the usual way. Power level* 1 / 1+ 2 / 2+ 3 / 3+ 4 / 4+ 5 / 5+ 6 / 6+ 7 / 7+ 8 / 8+ 9 Maximum operating time in hours 10 5 5 4 3 2 2 2 1 Safety shut-off if the touch controls are covered Your cooktop will turn off automatically if one or several of the touch controls remain covered for longer than 10 seconds, for example by fingers, food that boils over or by an object placed on them. The cooktop can now be used again. * Power levels with a "+" are only available with the extended power-level settings (see "Programming"). 28 Safety features Overheat protection Each burner is equipped with a temperature limiter. This feature automatically turns off the heating element before the glass ceramic surface becomes too hot. When the overheat protection is triggered, the heating element turns on and off even at the highest power level. Once the glass ceramic surface has cooled to a safe temperature the heating element will automatically turn back on. The overheat protection is activated by: ­ turning a burner on without putting a pan on it. [. . . ] Cooktops flush with the countertop Frame/Facet cooktops a Wall frame b Wall covering x = thickness of the wall covering c Countertop d Countertop cut-out e Minimum safety distance with flammable materials 2" (50 mm) with non-flammable materials 2" (50 mm) minus x 43 Installation Frame/Facet Cooktops Sealing Tiled surfaces The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service. The grouting a and shaded area under the appliance frame must be flat and even so that the frame will lie evenly and the sealing strip under the edge of the upper part of the appliance can provide an adequate seal against the countertop. 44 Installation dimensions KM 5840 a Spring clips b Front c Installation height d Connecting cable, Length = 56 11/16" (1440 mm) e Rating label 45 Installation dimensions KM 5860 a Spring clips b Front c Installation height d Connecting cable, Length = 56 11/16" (1440 mm) e Rating label 46 Installation dimensions KM 5880 a Spring clips b Front c Installation height d Connecting cable, Length = 56 11/16" (1440 mm) e Rating label 47 Installation Wood or solid surface countertop The exact positions of the spring clamps and the support bars (for beveled cooktops only) are shown in the "Installation dimensions" of each unit. Facet cooktops: A special sealing strip ensures the slip-proof seating of the cooktop in the cutout. [. . . ]