User manual RYOBI RE185

[. . . ] 3-4 Specific Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn the depth adjusting ring counterclockwise until the motor is to its highest position. NOTE: As the motor is rising, the gold spindle lock button has to be depressed until it clears the rear window. Align the indicator arrow on the depth adjustment ring with the indicator point on the base. NOTE: The rib is located on the inside of the base in line with the handle. Tighten the locking knob. DEPTH ADJUSTMENT RING INDICATOR ARROW 1/3 2 01 2 15/32 LOCKING ARM DEPTH ADJUSTMENT RING INDICATOR POINT RIB INSIDE THE BASE Fig. 4 GROOVE IN MOTOR HOUSING CAUTION: Do not tighten the locking knob without the motor installed in the base. Failure to heed this caution may result in permanent damage to the locking mechanism. 5 OPERATION TO SWITCH FROM PLUNGE BASE TO FIXED BASE OR D-HANDLE BASE See Figures 6 and 7. LOCKING KNOB WARNING: Failure to unplug the tool could result in accidental starting causing serious injury. The gold spindle lock button will not depress fully unless it is in line with the hole in the collet. If the gold spindle lock button does not depress fully, turn the collet nut while depressing the gold spindle lock button. If you find that extra force is needed or that the motor speed slows down considerably, turn off the router and reduce the depth of cut. When routing a groove that is too deep to safely cut in one pass, it is best to make the cut in several passes. Adjusting the depth of cut for the plunge router is different from adjusting the depth of cut for the fixed router. TO ADJUST DEPTH OF CUT FOR FIXED BASE OR DBASE ROUTERS See Figures 9 and 10. 9 DEPTH ADJUSTMENT RING INDICATOR ARROW WARNING: Failure to unplug the tool could result in accidental starting causing serious injury. Turn the depth adjusting ring counterclockwise until the tip of the cutter touches the flat surface. Turn the depth indicator ring until the zero lines up with the indicator point on the base. Position the router so that the cutter can extend below the subbase for desired depth of cut. NOTE: To adjust the depth of cut when the router is mounted to a router table, turn the depth adjustment ring until the cutter reaches the desired depth of cut. DEPTH INDICATOR RING 1/3 2 01 2 15/32 INDICATOR POINT Fig. 10 13 OPERATION TO ADJUST DEPTH OF CUT FOR PLUNGE BASE ROUTERS See Figures 11, 12, and 13. [. . . ] When routing with the template guide bushings, it is necessary to allow for size differences between the cutting edge of the cutter and the face of the guide bushing collar. ROUTER BASE TEMPLATE GUIDE SUBBASE SIZE DIFFERENCE WORKPIECE ROUTER BIT TEMPLATE GUIDE BUSHING COLLAR Fig. 24 20 OPERATION STRAIGHT GUIDE The straight guide is used as an edge guide that slides against the edge of a board to guide the cutter through the cut. Unplug your router. SUBBASE 7 16 3 32 1 16 0 1 32 12 15 32 WARNING: Failure to unplug your router could result in accidental starting causing serious injury. [. . . ]