User manual RYOBI RE180PL1

[. . . ] OPERATOR'S MANUAL ELECTRONIC PLUNGE ROUTER RE180PL1 VARIABLE SPEED ­ DOUBLE INSULATED Your new router has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Specific Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Plunge router until cutter reaches the approximate desired depth of cut. Lock plunge lock lever, temporarily locking cutter at desired depth of cut. Turn depth control knob clockwise until hex nut seats against stop flange. Always unlock plunge lock lever before setting depth of cut with depth control knob. Tighten lock knob securely. PLUNGE LOCK LEVER DEPTH ADJUSTMENT ROD COMPRESSION SPRING HEX NUT Fig. 9 DEPTH STOP KNOB LOCK KNOB STOP BAR ACCU-STOPTM MICRO-ADJUSTABLE DEPTH STOP EACH 90° ROTATION OF DEPTH STOP KNOB EQUALS 1/64 in. 10 SCALE ZERO RESET INDICATOR WITH RED LINE LOCK KNOB DEPTH STOP See Figures 10 and 11. The depth stop is located on the base of your router and makes it possible to make deep or heavy cuts in successive passes by use of the Accu-StopTM MicroAdjustable Depth Stop System. A preset cutting depth is achieved by plunging router until stop bar comes in contact with depth stop. The micro-adjusting feature provides alignment marks at each 90° rotation of the depth stop knob. Each 90° rotation of the knob changes depth of cut setting 1/64 in. A complete rotation (360°) of the depth stop knob changes the depth of cut setting 1/16 in. The Accu-StopTM Micro-Adjustable Depth Stop System provides for depth of cut changes to be made from 0 to 1/2 in. This initial setting of the stop bar can be "zero" depth of cut, or it can be any depth of cut setting that you choose as a starting point for a particular job to be performed. STOP BAR EACH COMPLETE ROTATION 360° OF DEPTH STOP KNOB EQUALS 1/16 in. 11 ADJUSTMENTS WARNING: Always wear safetey goggles or safety glasses with side shields when using your router. Failure to do so could result in dust, shavings, chips, loose particles, or foreign objects being thrown in your eyes resulting in possible serious injury. TO SET DEPTH STOP UNPLUG YOUR ROUTER. SPEED SELECTION CHART CUTTER SIZE MATERIAL SOFT MEDIUM HARD 1/4 3/8 1/2 A A 3/4 A A A E-F D-E A-B D-E C-D C-D B-C VERY HARD D-E C-D C-D B-C WARNING: Failure to unplug your router could result in accidental starting causing serious injury. Rotate depth stop until the highest depth stop is aligned with the stop bar. Place router on flat surface, and lower router until tip of cutter barely touches flat surface. Lock plunge lock lever to position cutter at "zero" depth of cut. The highest stop now becomes the "zero" depth of cut setting. TO INCREASE SPEED TO DECREASE SPEED VARIABLE SPEED CONTROL SELECTOR See Figure 12. [. . . ] Brush assembly is spring loaded and will pop out when you remove brush cap. Make sure curvature of brush matches curvature of motor and that brush moves freely in brush tube. Do not over torque. 21 MAINTENANCE PLUNGE LOCK LEVER See Figures 25, 26, and 27. TO ADJUST PLUNGE LOCK LEVER UNPLUG YOUR ROUTER. PLUNGE LOCK LEVER TO LOOSEN WARNING: Failure to unplug your router could result in accidental starting causing serious injury. [. . . ]