User manual RYOBI RCT350 SCHEMA ELECTRIC

[. . . ] However, under certain circumstances it may be possible for installation in these applications. Please contact a Miele Dealer or Miele's Technical Service Department with specific requirements. recommended not recommended not allowed 4 IMPORTANT SAFETY INSTRUCTIONS Cooktops should not be installed above a dishwasher, washer, dryer, freezer or refrigerator. A distance of at least 12" (305 mm) should be maintained between these two appliances. Install the appliance so that the power cord or gas piping does not come into contact with any portion of the cooktop which may become hot during use. [. . . ] Both the valve and the regulator must be easily accessible to the consumer after the appliance is installed. This appliance must be disconnected from the gas supply during any pressure testing performed in excess of 1/2 psi (3. 5 kPa). The machine must be isolated at test pressures equal to or less than 1/2 psi (3. 5 kPa). Any pipe connections must be made using a thread sealant approved for gas connections. Failure to correctly install these items could lead to a gas leak and subsequent explosion. Safety distances above the cooktop There must be a minimum safety distance of at least 30 inches (760 mm), b, between the top of the cooktop and any cabinet above it. The overhead cabinet depth, if unprotected, must not exceed 13 inches (33 cm). The minimum distance of combustible surfaces located above and to the sides of the cooktop, c, is 18" (457 mm). If the cabinet manufacturer recommends a different distance, follow that manufacturers recommendation. When installing the cooktop under a venting hood, always observe the minimum distances recommended by the hood manufacturer. Keep this instruction book in a safe place and pass it on to any future owner. 5 Cooktop dimensions KM 404 a Support brackets b Building in height plus 1/8" (3 mm) for the fixing screws * Please allow an additional 31/2" (90 mm) depth across the rear of the cooktop for clearance of the gas regulator (see "Gas connection" for illustration). 6 Cooktop dimensions KM 406 a Support bracket b Building in height plus 1/8" (3 mm) for the fixing screws * Please allow an additional 31/2" (90 mm) depth across the rear of the cooktop for clearance of the gas regulator (see "Gas connection" for illustration). 7 Countertop cut-out Installing one or multiple appliances: Cut out the countertop using the dimensions listed in the following table. Number of cooktops 1 2 3 4 All Miele combisets have the same length and width. Make sure that there is enough room under the countertop to allow for the depth of the various appliances. 70 for the USA This appliance is equipped with a three-prong grounding plug to prevent shock hazards. If the plug does not fit the outlet, have the proper outlet installed by a licensed electrician. or - Canadian Electrical Code Part I for Canada (CSA Standard C 22. 1). , WARNING - Disconnect the appliance from the main power supply before installation or service. To reduce the risk of electric shock, make sure that the appliance is properly grounded after installation. Power supply The automatic ignition requires that the cooktop be connected to a 120 VAC, 60 Hz power supply. (1. 2 m) long power cord that is ready for connection to the appropriate outlet. Please place the power outlet so that it is accessible after the appliance has been installed in the countertop. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. The manufacturer cannot be held responsible for damages caused by the lack, or inadequacy, of an effective grounding system. Note to the installer Please leave these instructions with the consumer or the appliance. 13 Gas connection Installation and service must be performed by a qualified installer, service agency or the gas supplier. This appliance must be installed with its own shut off valve and the included gas pressure regulator. Both the valve and the regulator must be easily accessible to the consumer to turn on or shut off the gas supply after the appliance is installed. This appliance and its individual shut off valve must be disconnected from the gas supply during any pressure testing performed in excess of 1/2 psi (3. 5 kPa), or isolated from the gas line by closing its individual manual shut off valve at test pressures equal to or less than 1 /2 psi (3. 5 kPa). [. . . ] Any pipe connections must be made using a thread sealant approved for gas connections. Failure to correctly install these items could lead to a gas leak and subsequent explosion. The gas connection must be made in accordance with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z 21. 1/NFPA 54 for the USA or - the current Can/CGA B 149. 1 and . 2 Installation Codes for gas burning appliances for Canada. Make sure that the maximum gas supply pressure before the gas pressure regulator is never more than 1 /2 psi for both natural gas or LP gas. [. . . ]