User manual RYOBI P500

[. . . ] OPERATOR'S MANUAL 5-1/2 in. , 18 VOLT LASER CIRCULAR SAW P500 BATTERIES AND CHARGERS SOLD SEPARATELY Your laser circular saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Failure to do so could result in possible serious personal injury. WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. PACKING LIST Circular Saw with Laser 5-1/2 in. Blade Blade Wrench AAA batteries (2) Lanyard (not included in combo) Operator's Manual Warranty Registration Card WARNING: To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when assembling parts. 10 ASSEMBLY ATTACHING THE BLADE See Figure 2. SPINDLE LOCK BUTTON WARNING: A 5-1/2 in. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guard, while thicker blades will prevent blade screw from securing blade on spindle. n Remove the battery pack from the saw. 2 3 0 2 2 LOWER BLADE GUARD HANDLE SPINDLE BLADE 0 505 4 n Depress the spindle lock button and remove the blade screw and outer blade washer. NOTE: Turn the blade screw clockwise to remove. CAUTION: To prevent damage to the spindle or spindle lock, always allow motor to come to a complete stop before engaging spindle lock. n Wipe a drop of oil onto the inner blade washer and outer blade washer where they contact the blade. SPINDLE LOCK WARNING: If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly. n Fit the saw blade inside the lower blade guard and onto the spindle. 2 3 3 20 2 NOTE: The saw teeth point upward at the front of the saw. NOTE: Never use a blade that is too thick to allow the outer blade washer to engage with the flats on the spindle. n Position the saw as shown, depress the spindle lock button, and remove the blade screw by turning it clockwise. n Remove the blade wrench from the storage area. 11 1 0 45 1 0 1 45 1 3 n Remove the blade wrench (5 mm hex key) from the storage area. INNER BLADE WASHER OUTER BLADE WASHER BLADE SCREW Fig. 2 LOWER BLADE GUARD LEVER TO LOOSEN SPINDLE LOCK SCREW 505 4 TO TIGHTEN Fig. 3 OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. CHARGING A COOL BATTERY PACK If battery pack is within normal temperature range, the red LED on charger will come on. NOTE: If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to your nearest Ryobi Authorized Service Center for electrical check. n Make sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only. n Place the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger. n Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger. n Red LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode. NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply. [. . . ] Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a Ryobi Authorized Service Center. n Install the two AAA batteries, aligning the positives (+) with positives (+) and the negatives (-) with negatives (-) as shown on the inside base of the laser. [. . . ]