User manual RYOBI EMM0001

[. . . ] OPERATOR'S MANUAL AIRgrip MultiTASKitTM EMM0001 Your product has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Before attempting to use this product, familiarize yourself with all operating features and safety rules. LASER LEVEL ATTACHMENT The laser level attachment emits a laser line of up to 30 feet and can be rotated 360°. AIRGRIPTM VACUUM TECHNOLOGY This product uses a vacuum base that can adhere to smooth surfaces. Using the vacuum seal prevents wall damage caused by nails or adhesive tape. The vacuum base is used to hold the MultiTASKitTM attachments and will support a weight of up to 15 lbs. Recessed grooves on the base can be used for attaching the end of a chalk line, and side slots are available for holding the end of a tape measure. LIGHTING ATTACHMENT The lighting attachment has three medium-intensity LED lights to provide light in dark work areas. It can be adjusted vertically up to 90° and rotated horizontally 360°. MAGNETIC TRAY ATTACHMENT The magnetic tray attachment can be used for holding screws, nuts, and bolts. It features two holes for holding screwdrivers or other small tools, and has a recessed front edge so tools can lie flat on the surface. The tray can be adjusted 90° vertically and 360° horizontally. CASE A zippered fabric case stores and protects the tool and accessories when not in use. MULTI-FUNCTION BASE The multi-function base allows the unit to be used on irregularly shaped walls or objects. It features built-in loops for a hook-and-loop strap and magnetic sides to hold securely to magnetic surfaces. The base also protects the unit when using on a dusty or dirty surface and during storage. HELPING HAND ATTACHMENT Use the helping hand attachment to assist in holding small amounts of weight up to 12 lbs. and will rotate 360° horizontally and 35° vertically. HOOK-AND-LOOP STRAP The hook-and-loop strap can be used along with the multifunction base to attach the unit to a variety of irregularly shaped surfaces. ROUGH-SURFACE ADAPTOR The rough-surface adaptor increases the number of surfaces on which the AIRgrip vacuum can be used. 7 ASSEMBLY UNPACKING This product has been shipped completely assembled. Press the button located on the side of the vacuum base to turn it ON and OFF. Always wait for at least 5 seconds between stopping and restarting the unit. USING THE AIR-GRIPTM VACUUM BASE See Figures 5 - 6. Vacuum grip technology allows the unit to be attached to most smooth surfaces. NOTE: The multi-function base is not used when mounting by vacuum grip. n Place the unit on the surface you want it secured to and push against the surface slightly to engage the seal. n Continue to hold the unit against the surface while pressing the on/off button. NOTE: Pulling the unit off the wall without releasing the vacuum could damage the tool. The grooves located in the vacuum base can be used to help hold a tape measure or chalk line when working unassisted. PUSH THE ON/OFF BUTTON TO TURN THE VACUUM BASE ON OR OFF Fig. By using the rough-surface adaptor, you can use the AIRgrip feature to position the unit on many non-smooth surfaces, including brick and painted cinder block. NOTE: The AIRgrip feature cannot be used with stucco or unpainted cinder block. n Position the rough-surface adaptor on the surface where you want to secure the vacuum base. n Place the unit against the adaptor on the dotted lines, and push in slightly to engage the seal. [. . . ] The light beam can be adjusted up to 90°, and the lighting attachment can be rotated 360°. Turn the lights on and off by depressing the on/off button located on top of the attachment. USING THE MAGNETIC TRAY ATTACHMENT See Figure 15. Position the tray in a horizontal or vertical position and tighten the locking knob to secure in place. The magnetic surface will hold small tools and/or nuts, bolts, screws, etc. [. . . ]