User manual RYOBI DP102L

[. . . ] DRILL PRESS DP102L Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n n n n n n n n n n n n n n n n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Featherboard A device used to help control the workpiece by guiding it securely against the table or fence during any ripping operation. FPM or SPM Feet per minute (or strokes per minute), used in reference to blade movement. Freehand Performing a cut without the workpiece being guided by a fence, miter gauge, or other aids. Kerf The material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut. Kickback A hazard that can occur when the blade binds or stalls, throwing the workpiece back toward operator. Miter Cut A cutting operation made with the workpiece at any angle to the blade other than 90°. Non-Through Cuts Any cutting operation where the blade does not extend completely through the thickness of the workpiece. Pilot Hole (drill presses) A small hole drilled in a workpiece that serves as a guide for drilling large holes accurately. Push Blocks and Push Sticks Devices used to feed the workpiece through the saw blade during cutting operations. A push stick (not a push block) should be used for narrow ripping operations. These aids help keep the operator's hands well away from the blade. Resaw A cutting operation to reduce the thickness of the workpiece to make thinner pieces. Revolutions Per Minute (RPM) The number of turns completed by a spinning object in one minute. Ripping or Rip Cut A cutting operation along the length of the workpiece. Riving Knife/Spreader/Splitter (table saws) A metal piece, slightly thinner than the blade, which helps keep the kerf open and also helps to prevent kickback. Saw Blade Path The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be or has been cut by the blade. Set The distance that the tip of the saw blade tooth is bent (or set) outward from the face of the blade. Snipe (planers) Depression made at either end of a workpiece by cutter blades when the workpiece is not properly supported. Through Sawing Any cutting operation where the blade extends completely through the thickness of the workpiece. Throw-Back The throwing back of a workpiece usually caused by the workpiece being dropped into the blade or being placed inadvertently in contact with the blade. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation. 9 FEATURES PRODUCT SPECIFICATIONS Chuck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The speed chart located on the cover inside the head assembly shows the recommended speed and pulley configuration for each drilling operation. To change the pulley configuration: n Lift head assembly cover from front to open. n Retighten the tension bolt. DRIVE BELT SPINDLE PULLEY MOTOR PULLEY TENSION BOLT Fig. 24 22 MAINTENANCE WARNING: When servicing, use only identical replacement parts. [. . . ]