User manual RYOBI BT2500

[. . . ] Atenie! èee Ò·ÓÍÓÈ Ë ÁÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ ÌeÓ·iÓËÏÓ ÔÓ~eÒÚ¸ ËÌÒÚÛÍ^ËË ËÁ ÌÒÚÓfle, , Ó ÛÍÓ, ÓÒÚ, . Este indispensabil sã citii instruciunile coninute în acest mod de utilizare înainte de montaj i de punerea în funciune. Przed montowaniem i uruchomieniem, koniecznie musicie si Pastwo zapozna z zaleceniami zawartymi w niniejszym sposobie uycia. Uwaga! Sous réserve de modifications techniques / Subject to technical modifications / Technische Änderungen vorbehalten / Bajo reserva de modificaciones técnicas / Con riserva di eventuali modifiche tecniche / Com reserva de modificações técnicas / Technische wijzigingen voorbehouden / Med förbehåll för tekniska ändringar / Med forbehold for tekniske ændringer / Med forbehold om tekniske endringer / Tekniset muutokset varataan / / A mszaki módosítás jogát fenntartjuk / Zmny technických údaj vyhrazeny / åÓ, , ÛÚ ·°Ú¸ , ÌeÒeÌ° ÚeiÌË~eÒÍËe ËÁÏeÌeÌËfl / Sub rezerva modificaiilor tehnice / Z zastrzeeniem modyfikacji technicznych English SAFETY INSTRUCTIONS Warning When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before attempting to operate this tool and save these instructions. Keep work area clean. When not in use, tools should be stored in a dry, high, or locked-up place, out of the reach of children. [. . . ] For example, do not use a circular saw for cutting tree limbs or logs. Do not wear loose clothing or jewellery that can get caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Never carry the tool by the cord or yank it to disconnect it from the socket. It is safer than using your hand and it frees both hands to operate the tool. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by a qualified technician at an Authorised Ryobi Service Centre. Your tool must be disconnected when not in use, before servicing, and when changing accessories such as blades, bits and cutters. Get into the habit of checking to see that adjusting keys and wrenches are removed from the tool before turning it on. Do not carry the plugged-in tool with a finger on the variable switch. When the tool is used outdoors, use only extension cords intended for outdoor use. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. To reactivate the hammer action, the mode selector (6) has to be reset to position (a). FITTING AND CHANGING BITS (FIG. 2) The device is equipped with an SDS-plus attachment system. You can use the selector to change modes even when the hammer drill is operating (at low speed). The selected mode is only activated once the variable switch (2) is pressed to start the tool. Note: Anti-clockwise rotation during impact drilling damages the drill bit. Deactivate the hammer action when using a diamond drill bit. Clean the bit and grease it with a thin layer of machine grease before inserting it into the chuck. Push and rotate the dust-free tool into the bit holder as far as it will go. Check that it has locked by pulling on it. REVERSING THE DIRECTION OF ROTATION The rotational direction switch (2) can only be activated when the tool is at a standstill!The rotational direction switch (2) has two positions: REMOVING THE BIT FROM THE SDS-PLUS SYSTEM (FIG. 3) Pull back the fastening sleeve (A) and remove the bit. SWITCHING ON/OFF Clockwise rotation: Set the rotational direction switch (2) to the right position. Anti-clockwise rotation: Set the rotational direction switch (2) to the left position. Re-sharpen or replace blunt drill bits. Speed control You can modify the speed at any time by pressing on the variable switch (2). [. . . ] Re-sharpen or replace blunt drill bits. Speed control You can modify the speed at any time by pressing on the variable switch (2). Lock-on button If you want to keep your hammer drill operating at a constant speed, press the lock-on button (3) while pressing the variable switch. To unlock this function, briefly press the variable switch (2) then release it. MAINTENANCE AUXILIARY HANDLE (FIG. 4) For reasons of safety, only use the hammer drill when it is fitted with the auxiliary handle. [. . . ]