User manual RYOBI AP10

[. . . ] Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your tool properly and only for what it is intended, you will enjoy years of safe, reliable service. Please fill out and return the Warranty Registration Card so we can be of future service to you. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS I Table of Contents, Introduction, and Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 I Rules For Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] I Slide the dust chute between the lock washer and the cutter head assembly, resting the dust chute on the rubber bumper. Note: To minimize sawdust accumulation on your workpiece, attach either a 2-1/2 in. (102 mm) shop vac hose to the end of the dust chute. SCREWS RUBBER BUMPER DUST CHUTE KNOBS DUST CHUTE Fig. 4 MOUNTING PLANER TO WORKBENCH If your planer is to be used in a permanent location, it is recommended you secure it to a workbench or other stable surface. When mounting the planer to a workbench, holes should be drilled through the supporting surface of the workbench. I Mark holes on workbench where planer is to be mounted using holes in planer base as a template for hole pattern. I Place planer on workbench aligning holes in the planer base with holes drilled in the workbench. I Insert four bolts (not included) and tighten securely with lock washers and hex nuts (not included). Install the lock washers and hex nuts from the underside of the workbench. Supporting surface where planer is mounted should be examined carefully after mounting to insure that no movement during use can result. If any tipping or walking is noted, secure workbench or support surface before beginning planing operation. I Mark holes on board where planer is to be mounted using holes in planer base as a template for hole pattern. I If properly adjusted, the depth of the finished piece should be the same as indicated on the thickness scale. I If out of adjustment, loosen the two screws holding the scale indicator and adjust the thickness indicator to the correct setting. I Retighten screws securely. THICKNESS SCALE SCALE INDICATOR SCREWS SCALE INDICATOR REPLANE INDICATOR ADJUSTMENT See Figure 9. Plane a scrap piece of wood and measure the depth of the finished piece. 8 DEPTH ADJUSTMENT HANDLE PHILLIPS SCREW WARNING: Failure to turn the planer off, remove the switch key, and unplug the planer could result in accidental starting causing possible serious personal injury. I Loosen the depth adjustment handle by unscrewing the phillips screw that holds it in place. I Remove the two socket head screws on the top (righthand side) of the planer. I Lift the top of the housing and carefully pull the right side of the housing up and off the planer base. I Lower the cutter head assembly until it stops against the stop screw. I Using an accurate ruler, check the measurement against the replane indicator setting. I If adjustment is necessary, use a wrench to loosen the lock nut and adjust the stop screw to the correct height. [. . . ] A light film of oil wiped on the face of the cutter blades will keep them rust-free. All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. No further lubrication is required. WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician at a Ryobi Authorized Service Center to avoid risk of personal injury. MOTOR/ELECTRICAL The universal motor is easy to maintain but must be kept clean. The sealed bearings are permanently lubricated and need no further attention. BRUSH REPLACEMENT See Figure 16. [. . . ]