User manual RYOBI 765R-SERIALS-502068326-THRU

[. . . ] Do not attempt to use the tool for a purpose for which it was not designed. The tool will give much better service if you do not use excessive force. Disconnect the plug when not in use, or when changing accessories, making adjustments, cleaning or working on tool. All tools should be kept out of the reach of children when not in use. [. . . ] Never attempt to free a stalled blade without first turning the saw OFF. When transporting the machine use only transportation devices and never use guards for handling or transportation. During transportation the upper part of the saw blade should be covered; for example by the guard. Use an extension table for supporting long workpieces during cutting operation. Ensure that the yellow warning label is removed from the table before use. DESCRIPTION(FIG. Rear extension table LOOSE PART LIST A: Mitre gauge assembly B: Rip fence assembly C: Blade guard assembly D: Leg stand (4pcs) E: Cross Brace (4pcs) F: Push stick G: Blister pack with screws H: Extension table SPECIFICATION Input voltage Watts Blade diameter Bore size No load speed Depth of cut at 90° Depth of cut at 45° Main table size Rear extension table size Sound pressure level Net weight 240V ~ 50Hz 1500W 254mm 15. 9mm 4500min-1 80mm 55mm 720mm(W) x 520mm(L) 440mm(W) x 125mm(L) 99 dB(A) 23. 5 kg WARNING! Noise can be a health hazard. When the noise level exceeds 85 db (A) be sure to wear ear protection. PROPER USE OF MACHINE This machine is designed to rip and cross cut wood exclusively up to maximum thickness of 80mm. For correct operation it must be fixed and operated as explained in this manual. RESTRICTIONS OF USE DO NOT cut timber greater than 80mm DO NOT cut metal, stone, rubber, plastic bones, etc. DO NOT weld machine. Page 3 DO NOT modify the machine or its guards/ controls DO NOT run the machine before removing all packaging. DO NOT use the saw for slotting (stopped groove). MOUNT THE ELEVATING AND LOWERING HANDLE AND THE TILTING HANDLE (FIG. 1) Mount the elevating handle(13) on the shaft on the left hand side of the saw and fix it by tightening the set screw in the handle (fig. 1). MOUNT THE BLADE (FIG. button to stop the machine. WARNING: Before turning the machine ON, make sure the blade guard is correctly installed and operating properly. OVERLOAD RESET BUTTON (FIG. In the event that your saw turns off during operation, turn the saw off and allow the motor to cool down for approximately 3 minutes. If the saw does not turn on, turn the switch off and check all cords for proper connection and retry. If it turns on and then cuts off while you are working, you may be trying to feed the workpiece too quickly or may be operating with a dull blade or may be trying to operate on an insufficient voltage. ELEVATING HANDLE (FIG. Please note - this handle will move sideways as the tilt or bevel is adjusted. Page 5 TILTING HANDLE (FIG. 13) The tilting handle(23) is used to tilt the blade for bevel cutting. Turn it clockwise to tilt toward the left and counterclockwise to tilt toward the right. MITRE GAUGE (FIG. 14) The head is locked in the desired position for crosscutting or mitre cutting by tightening the mitre gauge lock(10). Always lock it securely when in use by turning the mitre gauge lock(10). CROSSCUTTING (FIG. 14) Crosscutting is cutting wood across the grain at 90° or square with both the edge and the flat side of the wood. The mitre gauge (9) can be used on either of the grooves in the table. [. . . ] Should service become necessary during the warranty period, the owner should contact the RYOBI HELPLINE 1300 361 505 or contact the retailer from whom the product was purchased. In order to obtain guarantee service, the owner must present the sales docket and Guarantee Certificate to confirm date of purchase. This product is sold by the dealer or agent as principal and the dealer has no authority from the Company to give any additional guarantee on the Company's behalf except as herein contained or herein referred to. Guarantee Conditions This guarantee only applies provided that the Product has been used in accordance with the manufacturer's recommendations under normal use and reasonable care (in the opinion of the Company) and such guarantee does not cover damage, malfunction or failure resulting from misuse, neglect, abuse, or used for a purpose for which it was not designed or is not suited and no repairs, alterations or modifications have been attempted by other than an Authorised Service Agent. [. . . ]