User manual RYOBI 725R-41CD725A034

[. . . ] Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition. The other manual that came with your power tool, the parts manual, contains all the information that you need to order parts. I. 27-28 PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONS All information, illustrations and specifications in this manual are based on the latest product information available at the time of printing. Bump HeadTM is a trademark of Ryobi Outdoor Products. SERVICE INFORMATION Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer. [. . . ] Check for the following: · The operator is wearing eye protection and proper clothing. · The right arm is slightly bent, and the hand is holding the shaft grip. · The left arm is straight, and the hand is holding the handle. · The cutting attachment is parallel to the ground and easily contacts the vegetation to be cut without the operator having to bend over. Each time the head is bumped, about 1 inch (25. 4 mm. ) of trimming line is released. A blade in the cutting attachment shield will cut the line to the proper length if excess line is released. Line release becomes more difficult as the cutting line becomes shorter. NOTE: Do not rest the Bump HeadTM on the ground. CAUTION: Do not remove or alter the line cutting blade assembly. This may lead to serious personal injury or damage to the unit. Some line breakage will occur from: · Entanglement with foreign matter · Normal line fatigue · Attempting to cut thick, stalky weeds · Forcing the line into objects such as walls or fence posts TIPS FOR BEST TRIMMING RESULTS · Keep the cutting attachment parallel to the ground. Cutting with more than the tip will reduce cutting efficiency and may overload the engine. · Cut grass over 8 inches (200 mm. ) by working from top to bottom in small increments to avoid premature line wear or engine drag. Fig. Disconnect spark plug wire to ensure the unit will not start. FREQUENCY Before Starting Engine Every 10 Hours Every 50 Hours MAINTENANCE REQUIRED Fill fuel tank with correct oil and fuel mixture. Check spark plug condition and gap. REFER TO: Page 10 Page 20 Page 22 15 MAINTENANCE AND REPAIR INSTRUCTIONS LINE INSTALLATION FOR THE SPEEDSPOOL® Always use genuine Ryobi 0. 080 in. Larger line may make the engine overheat or fail. Trimming Line Eyelet WARNING: Never use metal-reinforced line, wire, or rope, etc. . These can break off and become a dangerous projectile. There are two methods to replace the SpeedSpool® trimming line. · Wind the inner reel with new line · Install a prewound inner reel Winding the Inner Reel With New Line NOTE: It Is unnecessary to remove the bump knob to install new trimming line. (2. 03 mm. ) trimming line, 10 feet (3 m. ) long. Line Loading Hole Fig. Do not push the line more than 1/2 inch (12. 7 mm. ) into the line locking hole. 18). WARNING: Always use the correct line length when installing trimming line on the unit. Hold the outer spool and turn the inner reel counterclockwise to line up the arrows on the outer spool and inner reel (Fig. 16). Top View Of The SpeedSpool® Outer Spool Line Locking Hole Fig. Pull the line from the outer spool until the line is tight against the inner reel (Fig. [. . . ] · The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel pick up/fuel filter, ignition module, spark plug and muffler. OWNER'S WARRANTY RESPONSIBILITIES: · As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator's manual. ROP recommends that you retain all receipts covering maintenance on your small off-road engine, but ROP cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. · As the small off-road engine owner, you should however be aware that ROP may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. · You are responsible for presenting your small off-road engine to a Ryobi Authorized Service Center as soon as a problem exists. [. . . ]