User manual RYOBI 400W BAND SAW 230MM EBW4023L

[. . . ] EBW4023L 230mm BAND SAW WITH LASER AND LIGHT OWNERS OPERATION MANUAL EBW4023L ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM Laser Specification EN60875-1: 1994+ A11: 1996+A2:2001 Laser class 2 Wave lengths: 650 nm Output Power: <1mW 9 9 18 56 1 EBW4023L 2 3 55 ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM 17 Laser Specification EN60875-1: 1994+ A11: 1996+A2:2001 Laser class 2 Wave lengths: 650 nm Output Power: <1mW 54 16 11 15 12 14 5 6 13 4 7 8 EBW4023L ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM Laser Specification EN60875-1: 1994+ A11: 1996+A2:2001 Laser class 2 Wave lengths: 650 nm Output Power: <1mW 19 20 4 4 20 20 21 22 20 23 7 Fig. 2 3 24 EBW4023L 2 ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM EBW4023L 17 ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM 16 Laser Specification EN60875-1: 1994+ Laser class 2 A11: 1996+A2:2001 Wave lengths: 650 nm Output Power: <1mW Laser Specification EN60875-1: 1994+ A11: 1996+A2:2001 Laser class 2 Wave lengths: 650 nm Output Power: <1mW 25 19 14 20 21 13 Fig. 8 24 EBW4023L 39 ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM Laser Specification EN60875-1: 1994+ Laser class 2 A11: 1996+A2:2001 Wave lengths: 650 nm Output Power: <1mW 33 24 15 35 38 34 36 37 Fig. 12 EBW4023L ATTENTION LASER RAYS DO NOT LOOK DIRECTLY INTO THE BEAM Laser Specification EN60875-1: 1994+ A11: 1996+A2:2001 Laser class 2 14 Wave lengths: 650 nm Output Power: <1mW 4 6 42 Fig. [. . . ] Turn the lever counterclockwise to unlock the blade guide assembly (24). Turning the blade guide knob (clockwise raises the blade guide assembly, counterclockwise lowers it), position the blade guide assembly about halfway between the saw blade and saw housing. Move the thrust bearing (39) to within 0. 4 mm (1/64") of the blade. Repeat this procedure on the lower thrust bearing located below the saw table. Replace the blade guard if no additional adjustments are to be made. SQUARING THE SAW TABLE TO THE BLADE (Fig. 9) Failure to turn the saw off, remove the switch key and unplug the saw could result in accidental starting causing possible serious personal injury. WARNING: The upper and lower blade guides and thrust bearings support the band saw blade during cutting operations. The adjustment of the guides and bearings should be checked whenever a different blade is installed. Failure to turn the saw off, remove the switch key and unplug the saw could result in accidental starting causing possible serious personal injury. The thrust bearings support the back edge of the blade during cutting. The blade should not contact the thrust bearings (39) when you stop cutting. It is important that both upper and lower thrust bearings be adjusted equally. NOTE: The thrust bearing screw is the upper cap screw located on the right side of the blade guide assembly. It is the lower cap screw on the right side of the saw housing below the saw table for the lower bearing. ADJUSTING THRUST BEARINGS, BLADE GUIDE SUPPORT, AND BLADE GUIDES (Fig. 10, 11, 12) Remove the blade guard by loosening the two set screws with 4mm hex key. Turn the lock knob counterclockwise to unlock the blade guide assembly. Turning the blade guide knob clockwise, raise the blade guide assembly as far as it will go. Place a small combination square (34) on the saw table beside the blade. Loosen the table lock knob and rotate the angle adjustment knob to tilt the saw table up or down to align table 90° to blade (0° position). Using a hex keys, adjust the zero stop set screw (33) until the set screw just touches the saw housing. Loosen screw on scale indicator with a phillips screwdriver and align scale indicator to zero. Replace the blade guard once the saw table has been squared. Remove the blade guard by loosening the two set screws with 4mm hex key. Loosen the bottom screw on the right side of the blade guide assembly using the 4 mm hex key. [. . . ] 20) Replace the 2x Button Cell (AG13 or LR44 or SR44) into the Button Cell Protection Tube (61). 21) Close the Laser Switch Box Cover (58) and tighten the M3 Tapping Screw (59). 20) Switch on the laser beam and turn on the Band Saw for cut operation. BRUSHES (Fig. 17) T prevent accidental starting that could cause possible o serious personal injury, turn off the saw, and unplug thesaw before working on the band saw. [. . . ]