User manual RYOBI 320W 1/2 SHEET SANDER KIT ESS3215V

[. . . ] Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. WARNING Do not attempt to operate this tool until you have read thoroughly and understood completely safety rules, etc. Failure to comply can result in accidents involving fire, electric shock or serious personal injury. Save owners manual and review frequently for continuing safe operation and instructing others who may use this tool. [. . . ] WARNING Do not throw sanding dust on an open fire because materials in fine particle form may be explosive. WARNING A suitable breathing respirator must be worn while sanding lead paint, some woods and metal to avoid breathing the harmful/toxic dust or air. PRODUCT SPECIFICATIONS Input Wattage No load speed Orbital diameter Weight 240 V 50 Hz 320 W 6000-12000 min-1 2. 2 mm 2. 2 kg n n n n n n n English APPLICATIONS Use only for the purposes listed below: n n n Sanding on wood surfaces. The electronic speed control allows the operator to adjust speed to meet varity sanding material from tough heavy grained timber to delicate veneer. WARNING Do not allow familiarity with your sander to make you careless. Remember, a careless fraction of a second is sufficient to inflict severe injury OPERATION WARNING Your sander should never be connected to power supply when you are assembling parts, making adjustments, assembling or replacing sandpaper, cleaning, or when not in use. Disconnecting sander will prevent accidental starting that could cause serious personal injury. I N S TA L L I N G SANDPAPER (13) FEATURES Your sander is suitable for sanding with coarse, medium, and fine grit sandpaper. It will produce a fine scratch free finish when used to sand with the grain on wood surfaces. It has been designed so that flush corner sanding on three sides of the sander is possible. Your sander has a comfortable palm grip handle that provides maximum one-hand comfort, and reduces operator fatigue during continuous sanding operations. Your sander also has a built in dust collection that collects dust through punched holes in the sandpaper and cushion. Before attempting to use your sander, familiarize yourself with all operating features and safety requirements. If replacing ahesive sandpaper, remove old sandpaper by peeling it off cushion. Variation Speed Control "ON / OFF" Switch Trigger Power Supplier Cord Dust Exhaust Sanding Pad Assembly Platen Live Tool Indicator Sandpaper Puncher Non-Adhesive Sandpaper Dust Bag Assembly Handle of Clamp Clamp Adhesive Sandpaper NOTE: Sand for a few minutes to soften the adhesive backing before attempting to remove old sandpaper. Position sandpaper, making sure front edge of sandpaper is aligned with front edge of the cushion, then carefully press sticky side of sandpaper on cushion. If the new sandpaper have a dust hole, then align holes in paper with holes in cushion, then carefully press fuzzy side of sandpaper against cushion as tightly as possible. n INSTALLING NON-ADHESIVE SANDPAPER (9) n n Lifting up the handle (11), and observing the sandpaper clamp (12) be lifting up also. n n Release down the handle and apply clamp downward pressure to conform sandpaper to platen. Lifting up another handle on opposite end of sander and insert loose end of sandpaper under clamp also. Multi-sheet of sandpaper can be installed at one time for convenience. WARNING Unsecured work could be thrown towards the operator causing injury. Hold your sander in front and away from you, keeping it clear of the workpiece. [. . . ] This product is sold by the dealer or service centre as principal and the dealer has no authority from the Company to give any additional guarantee on the Company's behalf except as herein contained or herein referred to. Guarantee Conditions This guarantee only applies provided that the Product has been used in accordance with the manufacturer's recommendations under normal use and reasonable care (in the opinion of the Company) and such guarantee does not cover damage, malfunction or failure resulting from misuse, neglect, abuse, or used for a purpose for which it was not designed or is not suited and no repairs, alterations or modifications have been attempted by other than an authorised service centre. This guarantee will not apply if the tool is damaged by accident or if repairs arise from normal wear and tear. The Company accepts no additional liability pursuant to this guarantee for the costs of travelling or transportation of the Product or parts to and from the service dealer or centre - such costs are not included in this guarantee. [. . . ]