User manual RYOBI 310BVR-SERIALS-304122405-THRU-611000000

[. . . ] The manufacturer shall not be liable for any damage resulting from the improper use of this saw. This machine is not designed to cut cylindrical pieces (such as logs or pipes), nor to cut metal. 2. 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 GENERAL SAFETY PRECAUTIONS Only the people who are already familiar with this machine and are aware of the dangers of its use are authorised to use it. Minors are only authorised to use this machine within the framework of occupational training under the supervision of a specialist. Any use of this machine other than the uses mentioned in this manual require the manufacturer's written approval. [. . . ] If you use a smaller-gauge and longer cable, you run the risk of causing a voltage drop which could affect the starting and warming up of the motor. Connecting cables and extension cables must be checked regularly to avoid insulation defects. Any damaged connecting element must be replaced immediately by an electrician. The power socket to which the machine is connected must be earthed in compliance with applicable standards and must be equipped with a fuse of at least 16 A or an L circuit breaker. The table saw must be protected by a 30 mA differential circuit breaker. 5. 2 5. 3 5. 4 5. 5 5. 6 6. 6. 1 6. 2 6. 3 SETTING UP YOUR SAW Use the purpose-made bore holes in the legs to secure the table. The switch can only be activated when the machine is connected to the power supply. When the voltage drops, the switch is activated via an undervoltage relay. The machine must be switched back on when the voltage is back to normal. When the motor is overloaded, the table saw is stopped via the motor protection device. If the motor was overloaded and therefore overheated, wait approximately 10 minutes before restarting the machine. There may be a sound signal lasting 12 to 15 seconds longer than usual (even if the sawblade is already stopped). 6. 4 6. 5 7. 7. 1 7. 2 7. 3 7. 4 7. 5 7. 6 7. 7 RECOMMENDATIONS PRIOR TO USING THE SAW Always disconnect the power plug before any maintenance operation or adjustment. You can then easily slide the riving knife to adjust it to the new diameter. 8 mm on a tangential axis in relation to the blade), carefully tighten the central screw (Fig. Once the adjustments have been made, carefully tighten both hexagonal screws (Fig. 3) To adjust the height of the sawblade, you must turn the wheel to the right to increase cutting height to the left to decrease cutting height A single turn of the wheel corresponds to an increase or decrease of 2 mm in cutting height. 12. ADJUSTING THE TILT OF THE SAWBLADE (Fig. Once the adjustment has been made, carefully tighten the locking lever. 13. TILT LIMIT (Fig. However, should it be necessary to make a few adjustments, loosen screw "c" then move angle limiter "d". By moving angle limiter "d" upwards, you can adjust the tilt angle from 1. 5 to 46. 5. 14. REPLACING THE SAWBLADE (Fig. Loosen the screw holding the table insert and remove the table insert. Mount the sawblade by carrying out the operation in the reverse order. 15. ACCESSORIES AND SPECIAL TOOLS (Fig. 6 - 7 - 8) Wedge for small workpieces Using the wood pusher and the push stick 16. CUTS CAUTION!Always comply with section 7 of this user's manual, "Recommendations prior to using the saw". [. . . ] Attach the long cross pieces to the legs, without tightening them down. Motor 15 F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants : EN 1870-1 : 1999, EN 292-2 : 1991 + A1 : 1995, EN 294 : 1992, EN 60204-1 : 1997 89/336 EWG, 73/23 EWG, 98/37 EG NL CE CONFORMITEITSVERKLARING Wij verklaren op onze eigen verantwoordelijkheid dat dit produkt voldoet aan de volgende normen of normatieve dokumenten. EN 1870-1 : 1999, EN 292-2 : 1991 + A1 : 1995, EN 294 : 1992, EN 60204-1 : 1997 89/336 EWG, 73/23 EWG, 98/37 EG GB CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents. EN 1870-1 : 1999, EN 292-2 : 1991 + A1 : 1995, EN 294 : 1992, EN 60204-1 : 1997 89/336 EWG, 73/23 EWG, 98/37 EG S EG FRSKRAN Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande normer och dokument. [. . . ]