User manual RYOBI 2075R

[. . . ] MODEL 2075r GAS TRIMMER OPERATOR'S MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U. S. or 1-800-265-6778 in CANADA IMPORTANT MANUAL DO NOT THROW AWAY INTRODUCTION THANK YOU Thank you for purchasing this quality product. This modern outdoor power tool is designed to provide many hours of useful service. This operator's manual provides you with easy-tounderstand operating instructions. [. . . ] Rotate the entire unit so that the cutting head is at a 30° angle to the ground (Fig. 11 Each time the head is bumped, about 1 inch (25. 4 mm) of trimming line is released. A blade in the string guard will cut the line to the proper length if excess line is released. Excessive line length will cause clutch to overheat and may result in serious personal injury. EDGING For edging with the trimming head attachment, locate and lock the release button into the 90° edging hole or 180° edging hole in the ClickLink system (Fig. 10). MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULE These required maintenance procedures should be performed at the frequency stated in the table. Disconnect spark plug wire to make sure the unit will not start. FREQUENCY Daily or Before Starting Engine Every 10 Hours Every 50 Hours MAINTENANCE REQUIRED Fill fuel tank with correct oil and fuel mixture. Check spark plug condition and gap. REFER TO: Page 8 Pages 14-15 Page 16 11 MAINTENANCE AND REPAIR INSTRUCTIONS LINE INSTALLATION FOR THE SPEEDSPOOL® The trimming line in the speed spool may be replaced by two different methods. · Winding the existing inner reel with new line · Installing a prewound inner reel TO INSTALL NEW TRIMMING LINE, IT IS NOT NECESSARY TO REMOVE THE BUMP KNOB. The Correct Line to Use WARNING: Always use genuine Ryobi replacement line. WINDING THE EXISTING INNER REEL WITH NEW LINE NOTE: Before installing new trimming line onto the existing inner reel, remove any old line from the SpeedSpool by pulling the line out of the line loading or locking holes (Figs. Line up the arrow on the inner reel with the arrow on the outer spool (Fig. WARNING: Always use the correct line length when installing trimming line on the unit. If longer line is used than specified in this manual, the line may not release properly. Insert 10 feet (2. 5 m) of . 080 in (2. 03 mm) trimming line into one of the two eyelets and push it up through the line loading hole in the inner reel (Fig. Pull the line away from the spool until the line is tight against the inner reel (Fig. 13 Bump Knob NOTE: Do not wind the inner reel before the second line is installed into the reel. Fig. Repeat the procedure with the second eyelet and use the same amount of line as specified in Step 2. Wind the inner reel counterclockwise until approximately four (4) inches of line remains outside of the eyelets in the outer spool (Fig. If you need to remove the Bump Knob to clean the spool or remove jammed, excess line, hold the outer spool, and unscrew the Bump Knob counterclockwise (Fig. TO INSTALL NEW TRIMMING LINE, IT IS NOT NECESSARY TO REMOVE THE BUMP KNOB. Fig. If winding the line becomes difficult or the line jams, pull the ends of the line away from the spool and continue winding the inner reel counterclockwise (Fig. Remove the Bump Knob, foam seal, spring, inner reel, and trimming line from the outer spool (Fig. [. . . ] Any replacement part that is equivalent in performance or durability may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer. The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel pick up/fuel filter, ignition module, spark plug and muffler. · · · · · · · · · · · 19 LIMITED TWO-YEAR WARRANTY RYOBI OUTDOOR PRODUCTS warrants each new RYOBI Product for two (2) years according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of original retail purchase. Any part of the RYOBI Product manufactured or supplied by RYOBI and found in the reasonable judgement of RYOBI to be defective in material or workmanship will be repaired or replaced by an authorized RYOBI service dealer without charge for parts and labor. [. . . ]