User manual RYOBI LCDI 1802

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual RYOBI LCDI 1802. We hope that this RYOBI LCDI 1802 user guide will be useful to you.


RYOBI LCDI 1802 : Download the complete user guide (2064 Ko)

Manual abstract: user guide RYOBI LCDI 1802

Detailed instructions for use are in the User's Guide.

[. . . ] 18 VOLT COMPACT HAMMER DRILL DRIVER OWNER'S OPERATING MANUAL LCDI1802 DESCRIPTION 1. Keyless chuck Torque adjustment ring Quick mode selector Two-speed gear train Rotation selector (forward/reverse/center lock) Depth rod stop Bit storage Trigger switch Mag TrayTM Handle screw Hex head hole Handle coller Teeth Depth stop rod clamp Auxiliary handle Battery pack (Not included) Latches Depress latches to release battery pack Reverse Forward Chuck jaws 22. Lock (tighten) Unlock (release) Low speed High speed Drive mode Drill mode Hammer mode To increase torque To decrease torque Bit Screws Bit holder Drilling depth Drill bit Scale To increase drilling depth To loosen To tighten To decrease drilling depth Chuck sleeve 1 2 3 4 6 8 5 9 7 Fig. 10 Important! It is essential that you read the instructions in this manual before operating this machine. [. . . ] BATTERy PROTECTION fEATURES RYOBI 18 V lithium-ion batteries are designed with features that protect the lithium-ion cells and maximise battery life. Under some operating conditions, these built-in features may cause the battery and the tool it is powering to act differently from nickel-cadmium batteries. During some applications, the battery electronics may signal the battery to shut down, and cause the tool to stop running. To reset the battery and tool, release the trigger and resume normal operation. NOTE: To prevent further shut down of the battery, avoid forcing the tool. If releasing the trigger does not reset the battery and tool, the battery pack is depleted. If depleted, the battery pack will begin charging when placed on the lithium-ion charger. Lock the trigger switch by placing the rotation selector in the center position. 3 SPECIfICATIONS Voltage Chuck Switch No load speed (Drill mode): -Lo speed -Hi speed Hammer speed (Blows per minute): -Lo speed -Hi speed Max. battery pack) MODEL BATTERy PACK (not included) BPL-1820 BPL-1815 BID1821 ABP1801 ABP-1815 18 V 2-13 mm Variable speed 0-400 min-1 0-1500 min-1 0-5200 min-1 0-19500 min-1 49 Nm 1. 68 Kg COMPATIBLE CHARGER (not included) BCL-1800 BCS618 BCL-1800 BCS618 ACR1800 260022029 OPERATION WARNING Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. English OPERATION Place the battery pack on the tool. Make sure the latches on each side of the battery pack snap into place and the battery pack is secured on the tool before beginning operation. WARNING Always remove battery pack from your tool when you are assembling parts, making adjustments, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury. Lock the trigger switch by placing the rotation selector in the center position. Therefore, the switch should always be locked when not in use or carrying at your side. The bit rotation is reversible and is controlled by a selector located above the trigger switch. With the drill 4 English OPERATION TWO-SPEED GEAR TRAIN (HI-LO) See Figure 6. The drill has a two-speed gear train designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of the drill to select either LO (1) or HI (2) speed. When using drill in the LO (1) speed range, speed will decrease and unit will have more power and torque. When using drill in the HI (2) speed range, speed will increase and unit will have less power and torque. [. . . ] Do not insert the drill bit into the chuck jaws at an angle then tighten. This could cause the drill bit to be thrown from the drill, resulting in possible serious personal injury or damage to the chuck. NOTE: Rotate the chuck body in the direction of the arrow marked LOCK to tighten the chuck jaws. Lock the trigger switch by placing the rotation selector in the center position. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE RYOBI LCDI 1802




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual RYOBI LCDI 1802 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.