User manual RYOBI 18V ONE CIRCULAR SAW LCS180G

[. . . ] LCS-180 CORDLESS CIRCULAR SAW OWNER'S OPERATING MANUAL DESCRIPTION 1. Blade 10. Blade Screw 11. Outer Blade Washer 12. Inner Blade Washer 13. To Loosen 14. To Tighten 15. Battery Pack(Not Included) 16. Depress Latches to Remove Battery Pack 17. Guideline 18. Blade Guide Notch 19. Front of Saw 20. Straight Edge (Not Included) 21. Workpiece (Not included) 22. C-Clamp (Not Included) 23. Bevel Scale 24. Motor Housing 25. Lower Blade Guard Handle 26. Pocket Cut 27. 0º Bevel Stop 28. Hex Nut 29. Adjustment Screw 30. Carpenter's Square (Not Included) 1 2 7 3 6 4 5 8 7 9 12 Fig. 1 11 10 Fig. 2 16 15 13 15 10 8 14 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 1 2 3 Fig. 9 Fig. 10 Fig. 11 Fig. 16 23 6 18 5 Fig. 17 17 Fig. 18 24 23 18 6 Fig. 19 29 6 50 Fig. 20 9 25 28 27 30 26 Fig. 21 Fig. 22 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. English GENERAL POWER TOOL SAFETY WARNINGS 3. [. . . ] WARNING To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the product when assembling parts. REMOVING THE BLADE See Figure 3. Position the saw as shown, depress the spindle lock button, and remove the blade screw by turning it clockwise. BATTERY PROTECTION FEATURES Ryobi 18 V lithium-ion batteries are designed with features that protect the lithium-ion cells and maximize 4 ATTACHING THE BLADE See Figure 2. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guard, while thicker blades will prevent blade screw from securing blade on English battery life. Under some operating conditions, these built-in features may cause the battery and the tool it is powering to act differently from nickel-cadmium batteries. During some applications, the battery electronics may signal the battery to shut down, and cause the tool to stop running. To reset the battery and tool, release the trigger and resume normal operation. NOTE: To prevent further shut down of the battery, avoid forcing the tool. If releasing the trigger does not reset the battery and tool, the battery pack is depleted. If depleted, the battery pack will begin charging when placed on the lithium-ion charger. Align the raised rib on the battery pack with the groove inside the saw, then slide the battery pack into the saw. Make sure the latches on each side of your battery pack snap into place and the battery pack is secured in the saw before beginning operation. CAUTION When placing battery pack in the tool, be sure raised rib on battery pack aligns with the bottom of the tool and latches into place properly. Improper installation of the battery pack can cause damage to internal components. OPERATION WARNING Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING Always wear safety goggles or safety glasses with side shields when operating products. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. REMOVING THE BATTERY PACK(Not Included) See Figure 4. Locate the latches on the side of the battery pack and depress them to release the battery pack from the saw. Therefore, switch should always be locked when not in use or carrying at your side. KICKBACK See Figures 5 - 8. [. . . ] Rest the front of the base flat against the workpiece with the rear of the handle raised so the blade does not touch the workpiece. Cutting in the reverse direction could cause the saw to climb up on the workpiece and back toward you. WARNING: To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the product when making adjustments. 8 CHECKING 0° BEVEL STOP Place the saw in an upside down position on a workbench. [. . . ]