User manual RYOBI 182823 RYOBY-TB3000

[. . . ] Owner/Operator Manual 2-Cycle Trimmer · · · · Safety Assembly Operation Maintenance Models TB3000 ­ 25cc Straight Shaft ©2000 MTD SOUTHWEST INC FORM 182823 (12/00) (10209 rev. A) Printed in U. S. A. Introduction THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. This operator's manual provides you with easy-to-understand operating instructions. [. . . ] NEVER add fuel additives directly to the unit's fuel tank. 1 US. (118 ml) For proper engine operation and maximum reliability, pay strict attention to the oil and fuel mixing instructions on the 2-cycle oil container. Using improperly mixed fuel can severely damage the engine. Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded gasoline in a separate fuel can. NOTE: One gallon (3. 8 liters) of unleaded gasoline mixed with one 4 oz. (118 ml) bottle of TROY-BILT 2-CYCLE OIL makes a 32:1 fuel/oil ratio. MIXING RATIO - 32:1 Fig. 4-1 Oil and Gas Mixing Instructions Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol or MTBE (ether). When using alcohol-blended fuel, use fresh fuel (less than 60 days old). Using Blended Fuels If you choose to use a blended fuel, or its use is unavoidable, follow recommended precautions. · Drain the tank and run the engine dry before storing the unit. Using Fuel Additives The bottle of TROY-BILT 2-Cycle oil that came with your unit contains a fuel additive which will help inhibit corrosion and minimize the formation of gum deposits. It is recommended that you use only TROY-BILT 2-Cycle oil with this unit. Gasoline is extremely flammable. Always stop the engine and allow it to cool before filling the fuel tank. Keep sparks and open flames at a distance from the area. Remove fuel cap slowly to avoid injury from fuel spray. Never operate the unit without the fuel cap securely in place. Add fuel in a clean, well ventilated area outdoors. Do not start the engine until fuel vapors dissipate. NOTE: Dispose of the old fuel/oil mix in accordance to Federal, State, and Local regulations. 10 Section 5 Operation Start/ On (I) Avoid accidental starting. To avoid serious personal injury, the operator and unit must be in a stable position while starting. STARTING INSTRUCTIONS Stop/ Off (O) Fig. 5-1 On/Off Stop Control Choke Lever Run (B) Start (A) Primer Bulb 1. If fuel hasn't entered the bulb, press three more times, or until it does. Continue pulling until the engine sounds as though it wants to run (normally 2 to 5 pulls). NOTE: Squeeze the throttle control until the engine has started and warmed up. NOTE: If the engine floods while trying to start, place the choke lever in the RUN (B) position. 5-3 Throttle Control STOPPING INSTRUCTIONS STARTING INSTRUCTIONS 1. [. . . ] Finger-Tip Trigger Unit Weight (No Fuel, with D-handle, Cutting attachment shield and Cutting attachment) . 18 inches (44. 0 cm) 20 Notes 21 MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD SOUTHWEST INC ("MTD") with respect with new merchandise purchased and used in the United States, its possessions and territories. MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator's Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water or damage because of other peril or natural disaster. [. . . ]