User manual RYOBI 1500W TABLE SAW 254MM ETS1526AL

[. . . ] Avoid wearing loose clothing, jewellery or anything that could get caught in moving parts. Use of safety goggles is recommended (normal glasses are not sufficient for eye protection). Face or dust masks should be used if dust is produced or working overhead. Keep proper footing and balance at all times; wear oil-resistant rubber footwear. [. . . ] Turn the elevating handle(13) (Fig. 1) in the counterclockwise direction to raise the blade shaft to its highest position (fig. 3). Remove the blade fixing nut by turning in a counterclockwise direction, then pull the outer flange from the shaft and the outer arbor. Mount the blade(15) (be sure that the teeth are facing downwards at the front side of the saw). Check again that the blade(15) is securely tightened and re-fit or adjust riving knife as necessary, before re-mounting the table insert(17). WARNING! Replace table insert when worn. MOUNT THE RIVING KNIFE (FIG. 4&5) If in place, remove the table insert(17)by removing the four phillips flat head screws. Insert the riving knife(20), so that the long slots in the riving knife fit around the hexagon socket head end screws (Fig. 4). Adjust the riving knife(20) so that the clearance between riving knife(20) and blade(15) is between 2 to 5mm (Fig. 5); then tighten the hexagon socket headed screws. Then check again that the blade is securely tightened and remount the table insert. 5a) Align the 3 holes of rear extension table (24) with 3 M6 x12, flat washer, spring washer and secure the rear extension table(24) to the main table. MOUNT THE RIP FENCE (FIG. 6&7) Loosen the rip fence lock knobs(5) on the sliding block(19), then slide the fence(6) onto the bolt heads and tighten the rip fence lock knobs(5) (Fig. 6) To lock the rip fence(6), slide the rip fence assembly until the indicator is pointing to Page 4 the desired setting. Then press rip fence lock handle (3) downwards (Fig. 7), to lock the fence into position. 8, 9&10) WARNING: · Do not use saw blades which are damaged or deformed. · Take care that the selection of the saw blade depends on the material to be cut. The Blade(15) has been adjusted at the factory, use a square to check that the blade is at a 90o angle to the table (Fig. 8) If adjustment is needed turn the tilting lock nut (while holding the adjustment in position) to fix the adjustment. Then loosen the indicator fixing screw, set the indicator of the scale(12) on the " 0o" marked then tighten the fixing screw(Fig. 9) After the 90o setting of the blade has been adjusted turn the tilting handle to the 45o (Fig. 10) side and adjust the 45o angle. Turn the adjustment nut so that the blade is on the 45o position and then tighten the lock nut. Live Indicator (FIG. 11) When the machine is connected with the power supply, the live indicator (4) will glow. If not, please check if the power plug is well connected. OPERATION ON/OFF MAGNETIC SWITCH (FIG. Should the supply be interrupted the switch will automatically default to the "OFF" position preventing a dangerous unexpected startup of the machine when the supply is restored. Adjust the Mitre gauge (9) to the desired angle. BEVEL CUTTING (FIG. 16) Bevel crosscutting is similar to crosscutting except that the wood is cut at an angle other than the 90° with the flat side of the wood or table. [. . . ] This guarantee will not apply if the tool is damaged by accident or if repairs arise from normal wear and tear. The Company accepts no additional liability pursuant to this guarantee for the costs of travelling or transportation of the Product or parts to and from the service dealer or agent - such costs are not included in this guarantee. Certain legislation, including the Trade Practices Act, 1974 (as amended) and other state and territorial laws give rights to the buyer and impose liability on the seller in certain circumstances. Nothing herein shall have the effect of excluding, restricting or modifying any condition, guarantee, right or liability imposed, to the extent only that such exclusion, restriction or modification would render any term herein void. A. B. N. [. . . ]