User manual ROYAL SOVEREIGN RSS LAMINATOR

[. . . ] WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign's sole and exclusive liability and the customer's sole and exclusive remedy under this warranty shall be, at Royal Sovereign's option, to repair or replace any such defective part or product. These remedies are only available if Royal Sovereign's examination of the product discloses to Royal Sovereign's satisfaction that such defects actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident, flood or other hazard. [. . . ] It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment. Part Name Laminator Quantity Picture 1 1 6/6 1 6/6 6 1 1 1 2 eh/Ve?Y. ?h?. W??@ fh?@eX/ Core - Bolts Dust Cover Spare Motor Fuse - FUSE(50T) 6. 3A RSR-685 RSR-1050 RSH-1050 RSH-1650 AC 200 ~ 220V, AC 230 ~ 240V, 50/60HZ Single phase Spare Main Power Fuse - FUSE(65TS) 15A / 20A(only RSH-1650) Roll film Samples 8 - 1/4"Hexa head Bolt (M6 20mm) 8 - Spring Washer( 6. 1) (Included with option only) 12 - 3/16"screw (M5 10mm). 12 - Spring Washer( 5. 1) (Included with option only) gh?@ ghH7 fh?M(J h?M02O h5J h@? 10/10 230V UL 220V EU 240V UK Front Feeder and Rear Rewinder Kit (Included with option only) 3 gh?@ ghH7 fhCONTROL PANEL When the machine is initially turned on, the LCD window will display the last working preset memory setting. 1 2 3 4 5 6 7 14 11 15 LCD 12 13 10 9 BUTTON 8 RSH Series No. PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RSS-685/ RSS-685N FILM ALIGNMENT KNOB O EMERGENCY SWITCH O SAFETY COVER O FRAME-PAPER GUIDE O FEED TABLE O HOT ROLLER X ROLLING SHOE X HOT SHOE O ASSEMBLY STAND O REMOTE CONTROL O FOOT PEDAL O TENSION CONTROL KNOBS O PRESSURE LEVER O CONTROL PANEL O UPPER IDLE BAR O TAKE-UP SWITCH O RELEASE LINER TAKE UP O TEMPERATURE DISPLAY C/ F ghY0@4V?? RSS-1050/ RSS-1050N O O O O O X X O O O O O O O O O O C/ F ghY0@4V?? RSR-685 O O O O O X O X O O O O O O O O O C& RSR-1050 O O O O O X O X O O O O O O O O O C& RSH-1050 O O O O O O X X O O O O O O O O O C& RSH-1650 X O O O O O X X O O O O O O O O O C& LCD Display 1. STND-BY ­ When STND-BY button is manually pressed or if the machine has been standing idle for 2 hours. In this mode, the temperature will automatically reset to 176°F (80°C). PRGM ­ Displays set memory. 6 RSS, RSR, RSH Series Control Buttons 1. UPPER: To change upper roller temperature by pressing button, then up or down arrow. LOWER: To change lower roller temperature by pressing button, then up or down arrow. 1 2 3 4 5 Inches Lamination 1/25" 3/16 ~1/4" 3/8 ~1/2" 3/5" RSH Series Only 15 Metric (mm) Lamination 1 5-7 10-13 NOTE: If you don't want to laminate, please place the pressure lever to the "Open position(NO. 5). " 7 8 RSS, RSR, RSH Series 9. USING FOOT PEDAL AND REMOTE CONTROL USING FOOT PEDAL Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot pedal to operate the laminator for "Hands Free Operation. " To activate the machine, press the foot pedal once and then release. USING REMOTE CONTROL Located on the left hand side of the rear of the laminator, to use press: 1. USING SLITTER Only the RSR & RSS series have slitters included 1. Adjust the left and/or right slitters by loosening the slitter adjuster knob (located between the front and rear rollers. ) (Figure 1) Figure 1 2. Activate the slitter by turning the slitter knob (located on the left side of the machine) clockwise. USING CROSS CUTTER The cross cutter is located on the rear exit table of the machine. [. . . ] Turn it until the supply roll films have some resistance (the tension varies depending on the thickness of a film, the thicker the film the more tension is required). Press Stop button when the leader board has completely exited the rear of the unit. Use the Cross Cutter to cut the leader board from the web (see page 9). Set the roller nip setting to the appropriate position for the lamination application. [. . . ]