User manual ROYAL SOVEREIGN RSC-1650H

[. . . ] This manual will provide you with complete operating and maintenance information. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating machine. keep this information for future refrence. comply any of the following safety procedures could result in serious personal injury. 1. To prevent the possibility of electrical shock, do not immerse machine in water or permit liquids to spill inside. Do not allow articles of clothing (neckties, scarves, papers, etc. ) near front or rear machine openings as they could get caught by rollers and be pulled inside, causing personal injury. [. . . ] Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it on the upper roller. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back. Allow some of the film with melted resin to stick to the Guiding Paper. Place the film from lower shaft beneath the film from the upper roller which is already meiting. and unwind films of both rollers 30~40cm(1~1. 3ft) for loosing the tension. The films will be fed into the machine and will come out from the rear site of machine. Check the status of lamination and place the pressure lever at lamination mode. -7EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 CONTROL OF ROLLER PRESSURE ***Methods of controlling pressure of the roller** 1. For setting, pull the pressure lever out and turn the lever to following the indication 2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C) 3. Laminating : For laminating 32~250micron thick film -8EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 INSTRUCTIONS FOR CONTROL PANEL We designed this machine standing by user's convenience. You can manipulate speed and temperature . ***Terms*** 3 4 3 2 5 2 6 6 1 1 -9EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 1. FUNCTIONS OF CONTROL PANEL 1 2 3 4 5 6 RUN/STOP BUTTON : Run or stop the rollers SPEED BUTTON : Increase or decrease speed LED OF SPEED : Display or speed LED OF TEMP. : Display temperature TEMP. BUTTON : Increase or decrease temperature REVERSE BUTTON : To make the rollers run backward 2. HOW TO USE BUTTONS 1 RUN / STOP BUTTON Push the RUN button to stop it. button in order to run rollers and push STOP 2 SPEED BUTTON Push the SPEED button button to increase the speed, push the speed to decrease the speed. 5 TEMP. The roller run backward. - 10 EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 LAMINATING STEPS 1. Put cold roll film on upper bar. (Set the same as methord of the HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. Set pressure lever at the proper position following to your lamination condition. After pressing the RUN/STOP button choose and set proper speed by using the SPEED button or . 5. [. . . ] 4. After work, you should clean the resin from the rollers before beginning the next operation 5. Please check the lubricant after long operation or you do not use for a long time. 6. Check the chain linking each gear is not loosened. The limit tension allowed is 3mm. - 13 EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 It's not out of order Symptom *Rollers do not operate after press RUN button in. Adjust film tension. ASSEMBLY PARTS PART NAME Core(76mm) 10 EA MODEL PART NAME Bolt(M8X12) 6 EA MODEL FUSE(50T) (AC250V 6. 3A) Washer(8) 1 RSC-1650H RSC-1650C BOLT CORE 1 8 6 RSC-1650H RSC-1650C FUSE(65TS) (AC250V 20A) - 14 EDNord - Istedgade 37A - 9000 Aalborg - Telefon 9633 3500 WARRANTY 1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized service center will repair this product free of charge if it is defective in material or workmanship. [. . . ]