User manual ROSEN R6500

[. . . ] SECURITY CODE O DVD CDC ENT M TV MEM ZOOM T REPEAT LOCATE OPTION VIEW WIDE CANCEL Before operating the unit, please read these instructions carefully OT01004710-20020606 Table of Contents 1. LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01 02 02 02 02 02 02 02 03 04 04 04 04 04 05 05 05 05 05 06 06 06 06 06 06 07 08 08 08 08 08 08 08 09 09 09 09 09 09 09 10 10 10 10 10 10 2. AUDIO SETTING Turning system on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] PLEASE NOTE: Any radio station which is weaker than the ASM threshold level, will not be stored. If less than six radio stations of sufficient signal strength are received in the selected band, the ASM system will search twice and then store the received stations in frequency order. To override an ASM stored frequency, follow "How to store radio stations into presets" section of handbook. Local / Distance Selector The LOCAL switch adjusts the radio's seek sensitivity in both wavebands. This will cause the seek tuning to stop only on local and strong radio stations with good reception and clear sound quality. To activate this function, press the multi function button 8 (below "LOC" on display). "LOC" will be shown on the display when active, "DX" will be shown when Local is turned off. The LOCAL setting has no effect during the "ASM" Auto Storing Process. FM "STEREO" Indicator "STEREO" will illuminate if a stereo radio station with sufficient strength is received in the FM band. If the stereo signal becomes weak, the radio will automatically and gradually switch to mono, but "STEREO" may still be shown on the display. Contrary to popular opinion, FM broadcasts are not static free, and although your new radio has a built-in electronic interference absorption circuit, some static will be evident from time to time, especially in areas without a direct line of sight to the transmitter. FLUTTER As VHF signals reflect off solid objects, it is possible to pass through areas of "Shadow" caused by tall buildings and/or hilly terrain, which effectively block out the signal. As the vehicle passes in and out of shadow areas, the level of signal will vary at a rapid rate, creating a flutter type of interference to the signal. DISTORTION (MULTIPATH) Distortion may occur when the direct signal from the transmitter and a reflected signal reach the antenna at the same time and either cancel or aid each other, like ghosting on a TV. This results in intermittent distortion of the signal whilst moving or constant distortion when stationary, such as at a traffic light or when parked. Should this distortion occur while stationary, moving the vehicle approximately one or two meters would on most occasions correct the problem. Circuitry has also been included in this radio to reduce this type of distortion. 06 2 DIN DVD PLAYER 6. 5" WIDE SCREEN MONITOR DVD OPERATION DVD OPERATION 2 DIN DVD PLAYER 6. 5" WIDE SCREEN MONITOR 24 SECURITY CODE The DVD player has the ability to play DVD, VCD, Audio CD, MP3 audio and MPEG video, as well as display JPEG and BMP images. Press the button to lower the front screen and access the disc insertion slot. Insert DVD or VCD, the disc will automatically load, indicated by "DISC LOADING" on the display. Once loaded the disc will start to play if there is no recorded menu. If the disc has more than one title, a menu screen will appear on the screen. To return to Title Page, press the MENU or TITLE buttons PLEASE NOTE: The On Screen Display (OSD) will show "INVALID DISC" if the disc region code does not correspond with the unit setting. The player will enter the resume playback feature, indicated by "PRESS PLAY TO CONTINUE" on the display. If the STOP button is pressed twice the resume playback function will be cancelled, indicated by "STOP" on the display. [. . . ] Scan Tracks Press the Multi function button corresponding to "TRACK SCN", to sequentially sample the first 10 seconds of all tracks on all discs in the magazine. During this time, "TRACK SCAN" will be highlighted on the display. Repeat current track Press the Multi function button corresponding to "TRACK RPT" to replay the current track. "TRACK RPT" will be highlighted on the display when this function has been selected. [. . . ]