User manual ROLLS WPM61

[. . . ] If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. Please visit our website at www. rolls. com, and register your new WPM61 by clicking on the Register Your Warranty Here line. Or, complete the Warranty Registration Card and return it to the factory. [. . . ] Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. THE EARPHONES USED WITH THE WPM61 MUST BE TRS STEREO, NOT MONO. USING MONO EARPHONES WILL DAMAGE THE RECEIVER. POWER SUPPLY The WPM61 does not include an external power supply. To purchase a Rolls PS27, contact Rolls at (801) 263-9053, or the retailer from which you purchased the system. 1 6 SPECIFICATIONS TRANSMITTER Frequency Response: Frequency Stability: Modulation: Transmitting Power: Spurious Emission: Distortion: Max AF Input Signal: Power Source: Current Consumption: Dimension (LxWxH): RECEIVER Sensitivity: Max. Power: Distortion: Frequency Stability: Hum and Noise: Power Source: Current Consumption: Dimension: 30 Hz - 15kHz +/-10 ppm (under 25 degrees C) 10kHz +/- 2kHz (1kHz 50mV) 10mW 80dB below carrier <1% 500mV 9V battery, or or external DC 12V 28mA +/-5mA 100x63x25 mm 2. 5 V min (under squelch control) 20mW min (at 16 speaker load) 3% max (under 10mW output) +/-0. 01% ppm (under 25 degrees C) - 50dB min 9V DC (alkaline recommended) DC 20mA max 60x25x100 mm DESCRIPTION TRANSMITTER 1. Low Battery LED indicator: Blinks when the power is turned on and a battery is installed, will stay lit if voltage is below 5. 5 to 6 Volts. Power LED Indicator: When the transmitter is being powered via battery, this light will blink momentarily during power-up. It will light continuously when the transmitter is operated via an external adapter. BATT/DC switch: External power source switch, this 8 6 k) c switch MUST be moved to the BATT location (ba 9 m) for the unit to operate on battery power. tto (bo T M61 Conversely, the switch MUST be moved to the WP ER DC location when the unit is to be operated I TT NS M T RA SS EL E via external 12 VDC power (Rolls PS27). Audio Input (Labeled AF IN): 1/8" (3. 5mm) jack connect to a line level monitor source. Battery Compartment: Location for 9V alkaline battery. DC RECEIVER 1. When the WPM61r is not in use, make sure this Power Switch is turned OFF. Power LED Indicator: Blinks when the Power Switch is first turned ON, will stay lit when the battery drops below 5. 5 to 6 volts and the receiver will no longer operate. Audio earphone output (Labeled AF OUT): 1/8" (3. 5mm) TRS stereo output jack. Volume Control: Adjusts the output level of the WPM61r to the earphone jack. The positive connection is toward the top of the WPM61r, the larger negative connection is toward the bottom. 3 2 WPM61R 4 W IREL ES S RE CEIV ER 1 Battery installation 5 5 (on back) 2 CONNECTION First, place the WPM61t transmitter in a flat location, preferably in a "line of sight" location where the transmitter and the receiver are not blocked by any obstacles. If the WPM61t is to be powered by a battery, make sure a fresh 9V alkaline battery is properly installed (see page 2). If the unit is to be powered by an external power supply (the Rolls PS27), connect the power supply to the DC12V jack on the side of the WPM61t and an AC outlet. [. . . ] As mentioned earlier, a "line of sight" arrangement of transmitter and receiver will achieve the best results. IMPORTANT In ear monitor systems operate best when the stage volumes are low. The high sound pressure levels produced by floor monitors can bleed through your earpieces and may effect the usefulness of the WPM61 system. CHANNEL SELECTION Each WPM61 system ships from the factory set at one of four pre-selected frequencies of operation. [. . . ]