User manual ROLLS RSE261

[. . . ] In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. [. . . ] All of this magic is achieved with our proprietary Spectrum Correction Encoding (SCE) Processing. SCE Processing is the use of all-pass filtering, frequency compensated gain adjustment, and compensated frequency domain delay. What this means to you is the elements of your sound are fanned out like a deck of cards, making each sound more audible and distinct, reducing the need for high volume and radical equalizer adjustment. 1 6 OPERATION Cont. DUAL MONO OPERATION Shown below is a connection example for using the two-channels of the RSE261 in a Dual Mono or independent channel configuration. For example, the 1/4" Input jack may be used while using the RCA output for that channel. INTRODUCTION Thank you for your purchase of the Rolls RSE261 Dual Sonic Exciter. We take pride in our products and appreciate any comments you may have regarding them. The RSE261 takes your program material and adds new life, clarity, and threedimensionality to your sounds. Please read the following manual carefully to ensure proper operation, and enjoy your new RSE261. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. ACOUSTIC PREAMP 2. Please complete the Warranty Registration Card and return it to the factory. SPECIFICATIONS Frequency Response: Input Impedance: OUTPUT INPUT INPUTS AC IN 12 VAC 2 OUTPUT INPUT MODEL RSE261 MADE IN U. S. A. 1 2 OUTPUTS 1 OFF +48V PHANTOM POWER R LEFT L LEFT LEFT LEFT INSERT INSERT INSERT INSERT THD: Hum & Noise: Indicators: TRIM POWER TAPE OUT TAPE IN RIGHT RIGHT RIGHT RIGHT LINE LINE LINE LINE TO RECORDING DEVICE OR AMPLIFIERS MIXER AUX 1 RIGHT OUT RET. LEFT AUX 1 OUT +60 TRIM +10 MIC 11/12 +60 TRIM +10 MIC 9/10 +60 TRIM +10 MIC 7/8 MIC 5/6 +60 TRIM +10 MIC 4 +60 TRIM +10 MIC 3 +60 TRIM +10 MIC 2 +60 TRIM +10 MIC 1 +60 +10 Max Output: Overload light thresh: Input/Output jacks Dimensions: Weight: Power: 20Hz to 40kHz 10K balanced 10K unbalanced 0. 007% typical -84 dB Power LED 2: Clip LEDs +18 dB +15 dB 1/4" unbalanced RCA unbalanced 12VAC, Rolls PS12 Adapter included 5 2 FRONT PANEL DESCRIPTION NOTE: The following descriptions are for both channels. BOTTOM DEFINITION BOTTOM DEFINITION ACTIVE ACTIVE OPERATION STEREO CONNECTION The diagram shown below is a stereo connection example for the RSE261. If you have an EQ or other processor after your mixer's main outputs, insert the RP261 between it and your crossover and/or power amplifier. [. . . ] REAR PANEL DESCRIPTION AC IN 12 VAC OFF +48V PHANTOM POWER R LEFT L LEFT LEFT LEFT INSERT INSERT INSERT INSERT POWER TAPE OUT TAPE IN 2 OUTPUT INPUT OUTPUT INPUT RIGHT RIGHT RIGHT RIGHT LINE LINE LINE LINE MODEL RSE261 MADE IN U. S. A. MIXER AUX 1 RIGHT OUT RET. LEFT AUX 1 OUT +60 TRIM +10 MIC 11/12 +60 TRIM +10 MIC 9/10 +60 TRIM +10 MIC 7/8 MIC 5/6 +60 TRIM +10 MIC 4 +60 TRIM +10 MIC 3 +60 TRIM +10 MIC 2 +60 TRIM +10 MIC 1 +60 TRIM +10 1 2 OUTPUTS INPUTS 1 AC IN: Connect to the included Rolls PS12 12 Volt AC adapter. CH 1 - 2 , 1/4" INPUTS: Unbalanced inputs for connection (normally) to the last device in the signal chain before the power amplifier. [. . . ]