User manual ROLLS RPB486

[. . . ] LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. [. . . ] IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RPB623 PHANTOM HEX 6 CHANNEL PHANTOM POWER SUPPLY PWR PHANT HANTOM HEX HE ROLLS CORPORATION SALT LAKE CITY, UTAH 6/00 OWNERS MANUAL INTRODUCTION Thank you for your purchase of the ROLLS RPB623 PHANTOM HEX 6 channel phantom power supply. This unit powers up to 6 condenser microphones with 48 volts of ultra clean phantom power. The outputs are 1/4" Tip-Ring-Sleeve balanced for easy connection to a digital multi-track recorder. To eliminate the possibility of any DC voltages, the RPB623 features pull-down resistors and isolation capacitors on all outputs. DESCRIPTION FRONT PANEL PWR INSTALLATION Mount the RPB623 in a sturdy rack. Connect microphones to properly shielded balanced cable, and connect the cable to the Input channels of the RPB623. The output impedance of the RPB623 will be the same as the impedance of your microphone. PHANT HANTOM HEX HE The green LED for each channel lights when that channel is in use. The RPB623 should be powered up and connected to the microphones before power is applied to the power amplifiers or recording device. [. . . ] Note: If you are connecting this to a mixer, adjust the mixer's gain or trim control carefully for a suitable input level. SW3 6. 8K C3A 47UF 1 1 +48V D11 LDLG +48V R7 100 C1B 47UF 2 2 XLR JACK F J1B 3 R2B 6. 8K C3B 47UF T1 SW SPST R8 100 D2 1N4001 D10 LDLG C2B 47UF R5B R1B 100K 6. 8K R5B 100K XLR JACK F J1E 3 R2E 6. 8K C3E 47UF C2E 47UF R4E R1E 100K 6. 8K R5E 100K 1 1 +48V +48V D7 LDLG 2 C5 470UF C4 470UF 2 G SPECIFICATIONS Connectors: Phantom Power Voltage: Max Phantom Power Current: Power Supply: Size (W x H x D): Weight: +48V 7812 U1 R11 100 6 ea. 1/4" TRS jacks (tip positive) 48 Volts 14 mA each channel Linear 120VAC 50/60Hz 19" x 1. 75" x 2. 5" (48 x 4. 5 x 12. 7) 4 lbs. 3 1 I O 3 D6 POWER LDSR AC1 AC PLUG C6 503 1 MCI 407 4024 D1 1N4001 D3 ZD12V ROLLS CORPORATION 5968 South 350 West Murray, UT 84107 D4 ZD12V D5 ZD12V PHANTOM HEX RPB623 Rev: Document Number: Size: A Ba RPB623. SCH S h e e t1 o f 1 [. . . ]