User manual ROLLS RP562

[. . . ] (2. 72 Kg) Power 120VAC (230VAC) 15VA RP562 Stereo Tube Sonic Exciter SUB FREQUENCY 100 ACTIVE SUB LEVEL BOTTOM DEFINI 50 175 SUB CLIP 35 Hz 200 -O O +20 0 10 0 Tube Sonic Exciter 20 10 6 31 0 24 VU 20 10 6 31 0 24 VU RP562 LEFT LEVEL RIGHT LEVEL A division of Rolls Corporation Salt Lake City, UT 12/97 OWNERS MANUAL STEREO CONNECTION WITH MONO SUB OUTPUT The diagram below shows how to connect the RP562 in a stereo configuration with a mono sub-woofer output. Again, remember to apply power to the RP562 and other devices before turning on the power amplifiers. OFF +48V PHANTOM POWER L POWER TAPE OUT TAPE IN R LEFT LEFT LEFT LEFT INSERT INSERT INSERT INSERT Thank you for your purchase of the Bellari RP562 Stereo Tube Sonic Exciter. The RP562 Stereo Tube Sonic Exciter is a two channel frequency compensation device designed to add life and animation to your sound. [. . . ] We take pride in our products and appreciate any comments you may have regarding them. Please read the following manual carefully to ensure proper operation, and enjoy your new RP562. Unpack and Inspect the RP562 package Your RP562 was carefully packed at the factory in a protective carton. Nonetheless, be sure to examine the unit and the carton for any signs of damage that may have occurred during shipping. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. Please complete the Warranty Registration Card and return it to the factory. WARNING For continued prootection against risk of fire, replace only with same type and rating of fuse. WARNING: To reduce the risk of electric shock or fire do not expose this device to rain or moisture. RISQUE DE CHOC - NE PAS ENLEVER SERIAL NUMBER 120 VAC 50/60 Hz 15 VA MODEL RA235 235- OUTPUTS CHANNEL ONE INPUTS CHANNEL ONE MADE IN U. S. A. SUB-WOOFER AMPLIFIER WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISQUE DE CHOC - NE PAS ENLEVER 4 1 FRONT PANEL DESCRIPTION SUB FREQUENCY: Sets the highest frequency allowed out of the Sub Woofer Outputs. The level is adjustable between - infinity (off) and a gain of + 20 dB. SUB CLIP LED: When lit, this LED indicates the signal level is 3 dB below clipping and there may be distortion in the Sub Woofer circuits. BOTTOM: Controls the low frequency cut/boost (flat or no cut/boost is at about 11 o'clock). There is a 0 to 1/2 turn spectrum spread from midrange to bass with this control as well as amplitude control. Setting it on 0 is flat response and minimal spread, on 10 is maximum spread and definition. PWR LED: Indicates that the RP562 is connected to an AC outlet, and the power is turned on. POWER SWITCH: Controls the primary power to the RP562. SUB FREQUENCY 100 ACTIVE OPERATION STEREO CONNECTION The diagram shown below is a stereo connection for your RP562. If you have an EQ or other processor after your mixer's main outputs, insert the RP562 between it and your power amplifier. If you are connecting the RP562 into a home stereo system, insert the Sonic Exciter between your signal sources such as tuners, cassette players, CD players etc. CAUTION: TO AVOID POSSIBLE SPEAKER OR AMPLIFIER DAMAGE, ALWAYS TURN ON THE RP562 AND OTHER PERIPHERAL EQUIPMENT BEFORE TURNING ON THE POWER AMPLIFIERS. [. . . ] ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. [. . . ]