User manual ROLLS RM203

[. . . ] LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. [. . . ] Each channel has a signal level control, a right/left balance control, an auxiliary level control, and a clip LED. INSPECTION 1. Your RM203 was carefully packed at the factory in a protective carton. Nonetheless, be sure to examine the unit and the carton for any signs of damage that may have occurred during shipping. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. Please complete the Warranty Registration Card and return it to the factory. 2 2 3-4 5 6 Back cover R102 2K C101 1U R103 47K C102 120PF D101 LDRR R2 10K R3 1K RCAX4 J21A REC OUT RCAX4 J21B REC OUT R15 100K 6 SPECIFICATIONS Input Impedance: Output Impedance: Max Input Level: Phase Shift: Connectors: Max Gain: S/N Ratio: THD IMD (SMPTE) Power Weight: Size: 10 k unbal. 50 bal R DESCRIPTION FRONT PANEL 1 2 3 4 5 6 7 8 9 10 CLIP PWR HEADPHONE/ AUX OUT 0 10 LEVEL CLIP 0 10 CLIP LEVEL 0 10 CLIP LEVEL 0 10 CLIP LEVEL 0 10 CLIP LEVEL 0 10 CLIP LEVEL 0 10 CLIP LEVEL 0 10 LEVEL CLIP 0 10 LEVEL CLIP 0 10 CLIP LEVEL 0 10 TAPE IN 0 10 AUX RETURN 0 10 MASTER LEVEL L 10 0 R L 10 0 R L 10 0 R L 10 0 R L 10 0 R L 10 0 R L 10 0 R L 10 0 R L 10 0 R L 10 0 +18 dBV < 10 deg. 20 Hz - 20 kHz 1/4" and RCA 26 dB Line 26 dB Aux >90 dB < . 003% < . 003% 120 VAC 50-60 Hz, 15 W 7 lbs (3kg) 19" x 1. 75" x 6. 5" (48cm x 4. 5cm x 17cm) RM203 BAL AUX BAL AUX BAL AUX BAL AUX BAL AUX BAL AUX BAL AUX BAL AUX BAL AUX BAL AUX Note: Channels One through Ten are identical. Channel Section Bal: Adjusts the relative level of the channel signal to the Right and Left outputs. Aux: Adjusts the amount of signal sent to the Auxiliary Output Level: Adjusts the overall signal level of the channel. Clip: When lit, indicates clipping of excessive level into the channel. Master Section Tape In: Adjusts the amount of input signal from the rear panel Tape In jacks. Aux Return: Controls the amount of signal received at the stereo Aux Return jacks. Headphone/Aux out: 1/4" TRS stereo jacks for monitoring the master right and left signals, also may be used as an alternative stereo output for connecting to another stereo amplifier. REAR PANEL MODEL RM203 S/N 203OUT TAPE IN R MONO MONO MONO MONO MONO MONO MONO MONO MONO MONO POWER 12 VAC MADE IN THE U. S. A. RIGHT OUT LEFT OUT AUX RIGHT/MON LEFT SEND AUX RTN AUX RTN RIGHT L LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT 10 9 8 7 6 5 4 3 2 1 Master Outputs Right and Left Out: 1/4" TRS balanced main output jacks. Right and Left Aux Return: 1/4" unbalanced jack, for connection to the right and left outputs of a signal processor, or they may be used as auxiliary inputs. Aux Send: 1/4" unbalanced jack, for connection to a signal processor input such as a multi-effects processor. [. . . ] AUXILIARY SEND/STEREO RETURN CONNECTION EXAMPLE MODEL RM203 S/N 203OUT TAPE IN R MONO MONO MONO MONO MONO MONO MONO MONO MONO MONO POWER 12 VAC MADE IN THE U. S. A. RIGHT OUT LEFT OUT AUX SEND RIGHT LEFT AUX RTN AUX RTN RIGHT L LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT RIGHT LEFT 10 9 8 7 6 5 4 3 2 1 MULTI-EFFECTS PROCESSOR INPUT RIGHT LEFT OUTPUTS Connect the RM203 Right and Left Outputs to an amplifier via two balanced TRS 1/4" jacks (two TS unbalanced jacks will work as well). Connect 1/4" unbalanced cables to the Aux Send to the Input of the signal processor, and connect each signal processor output to its corresponding Aux Return jack. Set the "Mix" control on your signal processor to 100% effect since the dry portion of the signal is mixed in the RM203. NOTE: The RM203 Aux Send jack may also be connected to an amplifier, then to speakers and used as a Monitor Send. 3 4 [. . . ]