User manual ROLLS CT1

[. . . ] LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation, use and service for a period of one (1) year from the date of purchase as shown on the purchaser's receipt. The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement (at our option), during the warranty period of any part which proves defective in material or workmanship under normal installation, use and service, provided the product is returned to Rolls Corporation, TRANSPORTATION CHARGES PREPAID. [. . . ] Some states do and MIDI cables not allow the exclusion or limitation of special, incidental or · Tests combinations of consequential damages so the the above above limitation or exclusion · Easy-to-read LED may not apply to you. This warranty gives you specific legal indication rights, and you may also have other rights which vary from state Any musician or sound person to state. It tests MIDI cables, plus, it will test combinations of the above. CT 1 CABLE DETECTIVE Cable Tester CABLE DETECTIVE CT 1 CT 1 CABLE DETECTIVE 1/GND 2/TIP 3/RING Salt Lake City, Utah Owners Manual INTRODUCTION Thank you for your purchase of the CT 1 CABLE DETECTIVE cable tester. This unit was designed with the working musician and sound person in mind. Read the following manual carefully to ensure proper operation and a full understanding of all the CT 1 functions. Tests for: Opens Shorts Intermittents Crossed wires To test RCA and 1/4" TS cables, plug each end of the cable into the proper jack and wiggle the cable around at different points on the cable. Watch the 1 and 2 LEDs, if either LED is off, or goes on and off - the cable is bad. The testing procedure for 1/4" TRS (stereo) and XLR cables is identical to the above, except watch the 1, 2 and 3 LEDs. Adapter type cables, such as 1/4" to XLR cables, may also be tested by plugging each end into it's proper jack on either side of the line. To test a MIDI cable, plug each end of the cable into the MIDI jacks and test as described above. Watch the 1 and 2 LEDs, if either LED is off, or goes on and off - the cable is bad. NOTE: WHEN TESTING A 1/4" MONO TO RCA CABLE, CONNECT THE 1/4" PLUG TO THE LEFT 1/4" JACK AND THE RCA TO THE RIGHT RCA JACK. [. . . ] PC 1 P H O N E 1 /4 J7 D2 LED P H O N E 1 /4 J6 OPERATION Insert one end of the cable to be tested on the left side of the line, located in the middle of the CT 1, and the other side of the cable on the right side of the line. See example below. RCA PC J5 RCA PC J8 J9 3 5 5 3 1 2 J10 D IN 5 M ID I T E S T 2 LED S 2 D IN 5 1 4 4 BATTERY STEREO & XLR C O R DS CABLE DETECTIVE CT 1 NO LEDS = BAD C O RD O R DEAD 1 L E D = S H O R T E D W IR E S 2 LED S = R C A, M O N O O R M ID I C O R D G O O D , O R C R O S S E D W IR E S IN 1 /4 "T R S , O R X L R CORD R O L L S C O R P O R A T IO N 5 1 4 3 S o u th M a in S tre e t S a lt L a k e C ity , U T 8 4 1 0 7 CABLE TESTER CT1 A 1/GND 2/TIP 3/RING 3 LED S = G O O D STER EO Document Number: Ba C T 1 . S C H Date: 22-Apr-1999 1 Sheet 1 of [. . . ]