User manual ROLAND XV-3080 QUICK START

[. . . ] Introduction Thank you for purchasing the Roland XV-3080 synthesizer module. To feel assured that you understand and can use all of the XV-3080's superior features, be sure to read the Owner's Manual in its entirety. The guide comprises two sections, a "Quick Start" manual and an "Owner's Manual. " The "Quick Start" manual (this volume) explains the XV-3080's basic functions using examples that are clear and easy to grasp. In addition to the XV-3080's basic operations, the "Owner's Manual" provides descriptions of more advanced uses and applications. [. . . ] La carte de série SRX s'installe dans l'emplacement EXP-E, F et la carte de série SR-JV80, dans l'emplacement EXP-A­D. 6 Getting Ready 1 2 Avant d'installer la carte d'extension, éteindre le XV-3080 et tous les appareils qui y sont reliés. N'enlever que les vis spécifiées sur le schéma suivant. 3 4 Enlever la plaque protectrice. Orienter le support à carte tel qu'indiqué sur le schéma. Support d'extension Wave série SRX série SR-JV80 7 Getting Ready 5 Dans l'appareil, vous trouverez des emplacements pour carte à extension de série SRX et SR-JV80. En vous référant au schéma ci-dessous, insérer le connecteur de la carte d'extension à l'emplacement correspondant tout en enfonçant simultanément le support à carte dans les trous de celle-ci. Conecteur Support d'extension Wave série SRX série SR-JV80 6 À l'aide de l'outil fourni à cet effet avec la carte, faire tourner en position "LOCK" le support à carte afin de bien la fixer. LOCK 7 Remettre la plaque à sa place et la fixer à l'aide des vis enlevées à l'étape 2. Ceci complète l'installation de la carte d'extension. 8 Getting Ready Les manipulations suivantes vous permettront de vérifier si votre carte a été correctement installée. 1 2 Allumer votre appareil en suivant les instructions de la p. 11. Appuyer sur la touche [SYSTEM]. · Are the volume levels on the XV-3080 and any amp or mixer that is connected turned down to the lowest settings? This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. 2 Press the XV-3080's [POWER] switch to turn on the power. fig. 03. e 3 1 Turn on the power to connected external devices. Turning Off the Power Before turning off the power, confirm the following. · Are the volume levels on the XV-3080 and any amp or mixer that is connected turned down to the lowest settings?· Have you saved your data, including data for any sounds you have created?122) 2 3 Turn off the power to connected external devices. Press the XV-3080's [POWER] switch to turn off the power. 11 Getting Ready Restoring the Factory Settings (Factory Reset) To ensure the XV-3080 operates correctly as described in the procedures found in the Owner's Manual when using the XV-3080 for the first time, be sure to restore the settings to their initial status as shipped. fig. 04. e 1 Press the [UTILITY] button, lighting the indicator. The Utility page appears in the display. fig. 05. e 2 Press the [ fig. 06. e ]/[ ] button to select UTIL 2 page. If any important data you may have created is stored in memory, then running this operation will cause such data to be lost. If there is any data you wish to retain, then save the data to a commercially available memory card or external MIDI device. 3 4 Press the [ blinking. ]/[ ] buttons so that FACTORY RESET is Press the [ENTER] button. fig. 07. e 12 Getting Ready 5 Press the [ENTER] button. The confirmation message "Are You Sure?" appears in the display. fig. 08. e 6 Press the [ENTER] button to execute Factory Reset. The PLAY page returns to the display. * If "Internal Write Protect= ON" message is displayed, press [DEC] to turn the setting OFF. After pressing [ENTER] to clear the message, press [ENTER] again to reset to the factory preset settings. For more information about the Internal Write Protect, please refer to Owner's Manual p. 122 13 Listening to the Demo Songs The XV-3080 features 8 internal demo songs. Now let's listen to the XV3080's awesome sounds and effects in Demo mode. fig. 09. e 1 Hold down the [EXIT] button and press the [ The DEMO PLAY page appears in the display. fig. 10. e ] button. All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws. 2 Rotate the VALUE dial or press the [INC] / [DEC] buttons to select the song you want to hear. * Select "CHAIN PLAY" to hear all songs performed in order, starting with the first song. 3 4 Press [ENTER] to start demo song playback. Press [EXIT] to stop the Performance and return to the status in Step 2. Pressing the [EXIT] button again while the XV-3080 is in this status takes you out of the DEMO PLAY page. * No data for the music that is played will be output from MIDI OUT. 14 Playing Sounds The XV-3080 comes with a full palette of onboard sounds. The sounds that are used for ordinary play are called "Patches. " Let's first listen to some Patch sounds in Patch mode. Playing Patches (Phrase Preview Function) Even with no MIDI keyboard or sequencer connected, the XV-3080 allows you to check sounds using a number prepared phrases that are perfectly matched to highlight each type of Patch. fig. 11. e 1 Press the [PATCH] button, lighting the indicator. The PATCH PLAY page appears in the display. fig. 12. e Certain Patches may not be set with a suitable range. In such cases, press the [ ]/ 2 Press and hold down the [VOLUME] knob. The prepared phrase using the Patch is played while the knob is depressed. [ ] button to adjust the range to appropriate conditions (Octave Shift function: Owner's Manual, p. 20). You can select other Patches by rotating the VALUE dial or pressing the [INC] / [DEC] buttons. Let's select some other Patches and check out some of the sounds available. 15 Playing Sounds Selecting Patches The XV-3080 comes with a "Patch Finder" feature that allows you to quickly find any Patch. Selecting Categories (Patch Finder Function) fig. 13. e 1 2 Press the [PATCH] button, lighting the indicator. Press the [PATCH FINDER] button, lighting the indicator. On the display, the Patch's number is replaced by its category. fig. 14. e Category 3 4 5 Press the [ ]/[ ] button to select the desired category. For details on the categories you can select, refer to Owner's Manual p. 17. Turn the VALUE dial or press the [INC]/[DEC] button to select any Patch from the currently selected category. Press the [PATCH FINDER] button to turn off its indicator. 16 Playing Sounds * If you press the VALUE dial after Step 3, the CATEGORY SELECT page appears. fig. 13a. e You can change to another category on this page by holding down the [SHIFT] button and pressing [INC]/[DEC]. Turn the VALUE dial or press the [INC]/[DEC] button to select a category, and then press [ENTER] to confirm the selection. What is a Patch?With the XV-3080, the basic sound component used in a usual performance is referred to as a "Patch. " A single Patch can be created by combining up to four different tones. Although a Patch could consist of only a single tone, using multiple tones allows you to create Patches with more complexity and vividness. Not only can you get fat, rich sounds by layering sounds using the internal Patches already available with the XV-3080 as is, you can also enjoy a high degree of control in creating sounds, for example having different tones sound depending on the range used, or the strength with which the keys are played. Furthermore, the XV-3080's parameters are arranged in sets for even more effective management of elements used in editing Patches, including the manner in which sounds are output, control of the outputs, and effects processing. What is a Tone? [. . . ] * To select Parts 9­16, press [1-8/9-16] to make its indicator light, and then press the desired PART SELECT [1/9]­[8/16] button. 24 Playing Sounds Assigning a different Patch to a Part This is how to change the Patch assigned to a Part in a Performance. Here we will change the patch assigned to Part 2 of Performance "PRA:01Seq:Template" to "018(Slap Bass). " fig. 29. e 1 2 3 4 At the PERFORM PLAY page, choose Performance "PRA:01Seq:Template. " Press [PART] to make its indicator light. Press the [ ] /[ ] button to select PART PATCH page. Make sure that the [1-8/9-16] indicator is not lit, and then press the PART SELECT [2/10] button to select Part 2. Its indicator will light, and the selected Part number will appear in the upper left of the display. fig. 30. e 5 Press the [ ]/[ ] button to move the cursor to Number. 25 Playing Sounds 6 Turn the VALUE dial to select 018(Slap Bass). Play your MIDI keyboard, and listen to how the sound has been changed. * Pressing the [UNDO] button restores Number to its original value, reselecting the original Patch. 7 1 2 3 4 5 Press the [EXIT] button to return to the PERFORM PLAY page. Changing the MIDI Reception Channel of Each Part Select the Performance you wish to use. Press the [MIDI] function select button to make its indicator light. Press the [ ]/[ ] button to choose the PART MIDI page. Press the [ ]/[ ] button to move the cursor to Channel. Press PART SELECT [1/9]­[8/16] to select the Part you wish to set. * To select Parts 9­16, press the [1-8/9-16] button to make its indicator light, and then press the desired PART SELECT [1/9]­[8/16] button. 6 7 Turn the VALUE dial or press the [INC]/[DEC] button to select the desired MIDI channel. Press [EXIT] to return to the PERFORM PLAY page. You can easily play multiple Parts ­ and their Patches ­ simultaneously by setting them to the same MIDI reception channel. 26 Playing Sounds Having Different Patches Play In Separate Ranges of the Keyboard (Split) In a Performance, by selecting the same MIDI receive channel for a number of parts and then changing the pitch range over which each part is to be played, you can thus divide the keyboard into separate ranges and assign a different Patch to each range. The split is one application of the layer technique (Playing Multiple Layered Patches). [. . . ]