User manual ROLAND VK-8M

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the VK-8M organ module. Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Conventions Used in This Manual · Button names are enclosed in square brackets; e. g. , [REVERB] button. [. . . ] If you want to adjust another parameter in the same edit mode, press [H-BAR PART] button and one of the [1]­[6] buttons to select the parameter, and turn the [VIBRATO AND CHORUS] knob to edit the value. While the parameters are being saved, the indicators of the [1]-[6] button will blink. 6. Parameters that are edited independently for each registration are saved as part of the registration (p. 37). 39 Advanced Use State of the AMPLIER type and REVERB type Indicators in Edit Mode When the setting is "0­127, " "0­10, " "0­15, " or "0­31. " When all of the AMPLIFIER type and REVERB type indicators are unlit, it indicates that the setting is at the minimum value (0). When all of the AMPLIFIER type and REVERB type indicators are lit, it means that the setting is set to the maximum value. As you increase the value, the AMPLIFIER indicators will successively light from the bottom. Min Max The setting will increase as you turn the [VIBRATO AND CHORUS] knob clockwise, and will decrease as you turn it counterclockwise. When you press the VIBRATO AND CHORUS [ON] button, this will return to the default setting. If the setting is an "ON or OFF" switch This is "off" (0) when all of the AMPLIFIER type and REVERB type indicators are unlit, and "on" when all of the AMPLIFIER type and REVERB type indicators are lit. OFF ON OFF ON This will be ON when the [VIBRATO AND CHORUS] knob is turned to the right, and OFF when turned to the left. When you press the VIBRATO AND CHORUS [ON] button, this will return to the default setting. When the setting is "-5­0­+5, " or "-100­0­+100" The illumination patterns of the AMPLIFIER type and REVERB type indicators offer an approximate reading of the value of a setting. For example, if a value is set to 0, the SPRING indicator under REVERB type, and the TYPE 1 indicator under AMPLIFIER type will both be lit. The AMPLIFIER type indicators indicate values in the negative direction, while the REVERB type indicators indicate values in the positive direction. Min 0 Max Turn the [VIBRATO AND CHORUS] knob clockwise to increase the value, or counterclockwise to decrease it. When you press VIBRATO AND CHORUS [ON], this will return to the default setting. 40 Advanced Use Settings That Are Saved for the Entire System Rotary-related Settings 1. Hold down the [BANK] buttons and press the ROTARY [SLOW/FAST] button. The indicators of the [1]­[6] buttons ([1]­[3] buttons) will blink. The [H-BAR PART] button lights up in amber. Button [1] [2] [3] Parameter ROTARY MIC DISTANCE ROTARY RANDOMIZE ROTARY INDICATOR SYNC SOURCE Page p. Press one of the [1] ­[6] buttons ([1]­[3] buttons) to select the parameter that you want to edit. Pressing the [HBAR PART] button causes the button's color to change and allows you to select all parameters. If you press the VIBRATO AND CHORUS [ON] button, the setting will return to the initial value. 4. When setting another parameter, press an [H-BAR The following parameters are assigned to each button. Button [1] [2] [3] [4] [5] [6] Parameter ROTARY WOOFER LEVEL ROTARY TWEETER LEVEL ROTARY WOOFER RISE TIME ROTARY TWEETER RISE TIME ROTARY WOOFER FALL TIME ROTARY TWEETER FALL TIME Page p. 42 PART] button and [1]­[6] button ([1]­[3] button) to select the parameter, then turn the [VIBRATO AND CHORUS] knob to change the setting. Press the [WRITE] button to finalize the settings of the rotary-related parameters. While the parameters are being saved, the indicators of the [1]­[6] buttons ([1]­[3] buttons) will blink. NOTE Never turn off the power while parameters are being saved. The [H-BAR PART] button lights up in green. Button [1] [2] [3] [4] [5] [6] Parameter ROTARY WOOFER SPREAD ROTARY TWEETER SPREAD ROTARY WOOFER SPEED SLOW ROTARY TWEETER SPEED SLOW ROTARY WOOFER SPEED FAST ROTARY TWEETER SPEED FAST Page p. [. . . ] 21, P. O. BOX 13520, Damascus, SYRIA TEL: (011) 223-5384 Roland Shanghai Electronics Co. , Ltd. (GUANGZHOU OFFICE) 2/F. , No. 30 Si You Nan Er Jie Yi Xiang, Wu Yang Xin Cheng, Guangzhou 510600, CHINA Tel: (020) 8736-0428 NEW ZEALAND Roland Corporation Ltd. 32 Shaddock Street, Mount Eden, Auckland, NEW ZEALAND TEL: (09) 3098 715 CZECH REP. K-AUDIO Kardasovska 626. TEL: (2) 666 10529 SWEDEN Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20 HONG KONG Tom Lee Music Co. , Ltd. [. . . ]