User manual ROLAND TD-4K SETUP GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ROLAND TD-4K. We hope that this ROLAND TD-4K user guide will be useful to you.


ROLAND TD-4K SETUP GUIDE: Download the complete user guide (5288 Ko)

You may also download the following manuals related to this product:

   ROLAND TD-4K (1 ko)
   ROLAND TD-4K ANNEXE 1 (1 ko)

Manual abstract: user guide ROLAND TD-4KSETUP GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Pull out the stand in the direction of the arrow, and use the screws you removed earlier to fasten the stand. 1. Finger-tighten all six of the tuning bolts in the sequence shown in the illustration. The appropriate amount of tension is one that will provide approximately the same striking response as on an acoustic drum. Use the drum key to adjust the tension as needed. Anchor bolt 1. 0 m (40") 04 Connect the pads to the sound module CR1 RD * Use cable ties to fasten the cables at the circled locations " " so that they do not interfere with your performance. [. . . ] Position the foot plate so that the anchor bolts rest on the screw holes of the foot plate. 3. Turn the anchor bolts to adjust the height so that the entire kick pedal is in contact with the floor and that the KD-8 does not wobble even when you press the pedal to make the beater strike the pad. When adjusting the height, lift the stand slightly while turning the anchor bolts so that the foot plate is not fastened together with it. 4. Screw the anchor bolts into the screw holes of the foot plate to fasten it. If you're using a drum mat, the KD-8 will be more stable if the pointed portion of the anchor bolts protrudes from the foot plate. If you're not using a drum mat, take care not to tighten the anchor bolts too far, so that you do not damage the floor or carpet. Other side Detailed explanation of each part FD-8 (Hi-hat control pedal) CY-5 (Hi-hat) CY-5 component names Pad face Bow portion NOTE Pedal plate Anchor bolt * The tips of the anchor bolts are sharp. * When using on hard-surfaced flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. CY-8 (Crash/Ride cymbal) CY-8 component names Pad face Bow portion Edge portion PD-8 (Tom) PD-8 component names Wing bolt Pad face Head Rim Stand xing screw Output jack FD-8 component names Edge portion Output jack Output jack Arm Control out jack * To adjust the travel of the pedal, loosen the arm bolt. NOTE * Continuous playing may cause dis-coloration of the pad, but this will not affect the Pad's function. PDX-8 (Snare) PDX-8 component names Tuning bolts Hoop Rim rubber Head sensor Head Wing nut Output jack Shell Head replacement procedure NOTE * Be sure to adjust the head tension of the PDX-8 before use. * Striking the head when the head tension is loose may damage the sensor and head. * Do not apply excessive force to the sensor and cushion located under the head. * Due to the nature of the materials used in the sensor of the PDX-8, changes in room temperature may affect the sensitivity of the sensor. The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted. * To obtain replacement heads, please contact the nearest Roland Service Center or an authorized Roland distributor, as listed in "Information. " Loosen Tighten Drum key 1. Remove all tuning bolts and washers. * Do not apply excessive force to the sensor and cushion located under the head. Doing so can interfere with accurate detection, and may damage it. Tuning bolts 2. For details, refer to the explanation on the opposite side of this leaflet. Holder Rim sensor * The rim rubber is one component that eventually wears out (depending on the number and strength of the rim shots performed), and will require replacement. Rim shots may not be performed correctly when the rim rubber is worn out. Consult Roland Service for more on replacing the rim rubber. Hoop Head Rim rubber Suitable position for rim shots Player Shell USING THE UNIT SAFELY IMPORTANT NOTES Placement Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets. The symbol alerts the user to important instructions or warnings. The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. [. . . ] Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the "Information. " · Never install the unit in any of the following locations. · Subject to temperature extremes (e. g. , direct sunlight in an enclosed vehicle, near a heating duct, on top of heatgenerating equipment); or are · Damp (e. g. , baths, washrooms, on wet floors); or are · Exposed to steam or smoke; or are · Subject to salt exposure; or are · Humid; or are · Exposed to rain; or are · Dusty or sandy; or are · Subject to high levels of vibration and shakiness. · This unit should be used only with a stand (MDS series) that is recommended by Roland. 006 005 004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . · Always keep the following parts including with the TD-4K and small components that may be removed out of the reach of small children to avoid accidental ingestion of these parts. Included Parts Cluches/Felts/Screws/Rotation stoppers Nuts/ Washers/Screws/Anchor bolts/Springs Removable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . · Do not insert hands or fingers into the locations indicated with arrows in the illustrations. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ROLAND TD-4K




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ROLAND TD-4K will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.