User manual ROLAND TD-12 V1.00 MIDI IMPLEMENTATION

[. . . ] 17, 2004 Version: 1. 00 Control Change Bank Select (Controller number 0, 32) Status BnH BnH 2nd byte 00H 20H 3rd byte mmH llH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (bank. 1 - bank. 128) processed as 00H 1. Receive data Channel Voice Messages * * Following Channel Voice Messages can be received in [SETUP]-[MIDI]-[MIDI CH] Tx/Rx Channel. Not received when [SETUP]-[MIDI]-[MIDI CH] Rx/Rx Switch is set to "OFF. n = MIDI channel number: mm = Bank number MSB: ll = Bank number LSB: * * Note Off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) * Only the channels assigned to the backing part can be received. Bank select processing will be suspended until a program change message is received. [. . . ] When instruments are selected for the backing part, bank selects for the respective instruments are sent. When a pattern is selected, the corresponding bank select for the instrument in each part is transmitted (except for the drum part). Modulation (Controller number 1) Note On Status 9nH 2nd byte kkH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 01H - 7FH (1 - 127) Status BnH 2nd byte 01H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: vv = Control value: n = MIDI channel number: kk = note number: vv = note on velocity: * * * * In the channel assigned to the durm part (or percussion part), after a pad is struck or the hi-hat control pedal is in the foot closed (splash) position, the note number set for the drum kit is transmitted. When a brush sweep is played on the SNARE pad with the [KIT]-[FUNC][BRUSH] Brush Switch set to ON, the corresponding note number set by means of [INST]-[CONTROL]-[BR MIDI] Brush Note No. When cross sticks are played on the SNARE pad with the [KIT]-[XSTICK] XStick Switch set to ON, the note number set by means of [INST]-[CONTROL]-[BR MIDI] XStick Note No. In the channel assigned to the durm part, the note number transmitted when the hi-hat pad is srtuck (open, closed) switches with the value set with [SETUP]- * * * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to MODULATION, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to MODULATION, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. 6 TD-12 MIDI Implementation Breath Controller (Controller number 2) Status BnH 2nd byte 02H 3rd byte vvH 0H - FH (ch. 1 - 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow * * The part volume ([PATTERN]-[PART]-[MIXER]-[VOLUME]) information is transmitted when set. The volume of each part in a pattern is transmitted when the pattern is selected (except for the drum part). n = MIDI channel number: vv = Control value: Panpot (Controller number 10) Status BnH 2nd byte 0AH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 40H - 7FH (Left - Center - Right) * * * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to BREATH, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to BREATH, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. n = MIDI channel number: vv = Panpot: * * * This is transmitted only on the channels which are assigned to the backing part. The backing part pan ([PATTERN]-[PART]-[MIXER]-[PAN]) information is transmitted when set. The backing part pan is transmitted when the pattern is selected. Expression (Controller number 11) Status BnH 2nd byte 0BH 3rd byte vvH 0H - FH (ch. 1 - 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow Foot Controller (Controller number 4) Status BnH 2nd byte 04H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: vv = Control value: n = MIDI channel number: vv = Control value: * * * * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to FOOT, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to FOOT, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to EXPRESSION, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. [. . . ] In a case in which two or more messages consecutive messages have the same status, MIDI has a provision called "running status" which allows the status byte of the second and following messages to be omitted. B3 (B3) (B3) (B3) (B3) (B3) 64 00 65 00 06 0C 26 00 64 7F 65 7F MIDI ch. 4, lower byte of RPN parameter number: (MIDI ch. 4) upper byte of RPN parameter number: (MIDI ch. 4) upper byte of parameter value: (MIDI ch. 4) lower byte of parameter value: (MIDI ch. 4) lower byte of RPN parameter number: (MIDI ch. 4) upper byte of RPN parameter number: 00H 00H 0CH 00H 7FH 7FH * In other words, the above messages specify a value of 0C 00H for RPN parameter number 00 00H on MIDI channel 4, and then set the RPN parameter number to 7F 7FH. RPN parameter number 00 00H is Pitch Bend Sensitivity, and the MSB of the value indicates semitone units, so a value of 0CH = 12 sets the maximum pitch bend range to ±12 semitones (1 octave). (On this device, the LSB of Pitch Bend Sensitivity is ignored, but the LSB should be transmitted anyway (with a value of 0) so that operation will be correct on any device. ) Once the parameter number has been specified for RPN, all Data Entry messages transmitted on that same channel will be valid, so after the desired value has been transmitted, it is a good idea to set the parameter number to 7F 7FH to prevent accidents. [. . . ]